STM32CubeF4

/**
  @page RTC_TimeStamp RTC Time stamp Example
  
  @verbatim
  ******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
  * @file    RTC/RTC_TimeStamp/readme.txt 
  * @author  MCD Application Team
  * @brief   Description of the RTC Time Stamp example.
  ******************************************************************************
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  @endverbatim

@par Example Description 

This example guides you through the different configuration steps by mean of HAL API 
to ensure Time Stamp configuration using the RTC peripheral.

At the beginning of the main program the HAL_Init() function is called to reset 
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 180 MHz.

The RTC peripheral configuration is ensured by the HAL_RTC_Init() function.
This later is calling the HAL_RTC_MspInit()function which core is implementing
the configuration of the needed RTC resources according to the used hardware (CLK, 
PWR, RTC clock source and BackUp). You may update this function to change RTC configuration.

LSE oscillator clock is used as RTC clock source. LSE oscillator clock usually 
delivered by a 32.768 kHz quartz.
The user can use also LSI as RTC clock source. The user uncomment the adequate 
define on the main.h file.

HAL_RTCEx_SetTamper()function is called to initialize the tamper feature.
HAL_RTCEx_SetTimeStamp_IT()function is then called to initialize the time stamp feature 
with interrupt mode. It configures The Time Stamp pin to be falling edge and enables
the time Stamp detection on tamper pin.
HAL_RTC_SetTime()and HAL_RTC_SetDate() functions are then called to initialize the 
time and the date.

The program behaves as follows:

1. After startup the program configure the RTC (Time date) and enable the feature 
   timeStamp. LED1 is on means that the RTC is configured and the time is displayed.

2. Applying a low level on the Time Stamp pin (PC13) by pressing to Tamper button, 
   a time stamp event is detedced and the calendar is saved in the time stamp structures.
   Each time the user presses on tamper button, LED4 toggles.

The time stamp and the current time are displayed on the LCD integrated on the eval board
if the user uncomment the define USE_LCD in main.h file.
If the user comment USE_LCD, the current time and Time Stamp are updated and displayed 
on the debugger in aShowTime and aShowTimeStamp variables.

LED1 is turned ON when the RTC configuration is done correctly.
LED4 is turned ON/OFF when the timestamp event is produced.
LED3 is turned ON in  the case of error.
    
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
      based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
      a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
      than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
      To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
      
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
      to have correct HAL operation.
      
@note  Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select the RTC clock source; in this 
       case the Backup domain will be reset in order to modify the RTC Clock source, as consequence RTC  
       registers (including the backup registers) and RCC_BDCR register are set to their reset values.


@par Directory contents 

  - RTC/RTC_TimeStamp/Inc/stm32f4xx_hal_conf.h    HAL configuration file
  - RTC/RTC_TimeStamp/Inc/stm32f4xx_it.h          Interrupt handlers header file
  - RTC/RTC_TimeStamp/Inc/main.h                  Main program header file  
  - RTC/RTC_TimeStamp/Src/stm32f4xx_it.c          Interrupt handlers
  - RTC/RTC_TimeStamp/Src/main.c                  Main program
  - RTC/RTC_TimeStamp/Src/stm32f4xx_hal_msp.c     HAL MSP module
  - RTC/RTC_TimeStamp/Src/system_stm32f4xx.c      STM32F4xx system clock configuration file

@par Keywords

RTC, Timer, Timestamp, Counter, LSE, LSI, Current time, Real Time Clock

@par Hardware and Software environment

  - This example runs on STM32F42xxx/STM32F43xxx devices.
    
  - This example has been tested with STM324x9I-EVAL RevB evaluation board and can be
    easily tailored to any other supported device and development board.    


@par How to use it ? 

In order to make the program work, you must do the following :
 - Open your preferred toolchain 
 - Rebuild all files and load your image into target memory
 - Run the example

 * <h3><center>&copy; COPYRIGHT STMicroelectronics</center></h3>
 */