STM32CubeF4

/**
  @page PWR_BOR PWR Brown Out Reset (BOR) example
  
  @verbatim
  ******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
  * @file    PWR/PWR_BOR/readme.txt 
  * @author  MCD Application Team
  * @brief   Description of the PWR Brown Out Reset (BOR) example.
  ******************************************************************************
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  @endverbatim

@par Example Description 

This example shows how to configure the programmable BOR thresholds using the 
FLASH option bytes.

By maintaining the Key push-button pressed at Reset, the new BOR level will be 
programmed. To modify the BOR threshold, select the voltage range using the 
appropriate line "#define BOR_LEVEL OB_BOR_XXXX" in main.c file.

LED1 is toggling to indicate that the reset is released and the system is in RUN
mode otherwise the BOR is maintaining the reset.

@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
      based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
      a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
      than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
      To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
      
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
      to have correct HAL operation.

@par Keywords

Power, PWR, EXTI, BOR, Interrupt, Wakeup, External reset

@par Directory contents 

  - PWR/PWR_BOR/Inc/stm32f4xx_hal_conf.h     HAL configuration file
  - PWR/PWR_BOR/Inc/stm32f4xx_it.h           Interrupt handlers header file
  - PWR/PWR_BOR/Inc/main.h                   header file for main.c
  - PWR/PWR_BOR/Src/system_stm32f4xx.c       STM32F4xx system clock configuration file
  - PWR/PWR_BOR/Src/stm32f4xx_it.c           Interrupt handlers
  - PWR/PWR_BOR/Src/main.c                   Main program
  - PWR/PWR_BOR/Src/stm32f4xx_hal_msp.c      HAL MSP module


@par Hardware and Software environment

  - This example runs on STM32F429xx/STM32F439xx devices.
  
  - This example has been tested with STMicroelectronics STM324x9I-EVAL RevB 
    evaluation boards and can be easily tailored to any other supported device 
    and development board.

  - STM324x9I-EVAL RevB Set-up
    - Use LED1 connected respectively to PG.06 pin
    - Use the Key push-button connected to pin PC13 (EXTI Line13)


@par How to use it ? 

In order to make the program work, you must do the following :
 - Open your preferred toolchain 
 - Rebuild all files and load your image into target memory
 - Run the example

 * <h3><center>&copy; COPYRIGHT STMicroelectronics</center></h3>
 */