mirror of
https://github.com/STMicroelectronics/STM32CubeF4.git
synced 2025-05-10 19:29:12 +08:00
100 lines
4.3 KiB
Plaintext
100 lines
4.3 KiB
Plaintext
/**
|
|
@page PWR_STOP PWR Example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file Examples_MIX/PWR/PWR_STOP/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the PWR_STOP example.
|
|
******************************************************************************
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics. All rights reserved.
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example shows how to enter the system in STOP with Low power regulator mode and wake-up from this
|
|
mode using external RESET or wake-up interrupt (all the RCC functions calls use
|
|
RCC LL API for footprint and performance improvements).
|
|
|
|
In the associated software, the system clock is set to 100 MHz, an EXTI line
|
|
is connected to the user button through PC.13 and configured to generate an
|
|
interrupt on falling edge upon key press.
|
|
The SysTick is programmed to generate an interrupt each 1 ms and in the SysTick
|
|
interrupt handler, LED2 is toggled in order to indicate whether the MCU is in STOP with Low power regulator mode
|
|
or RUN mode.
|
|
|
|
5 seconds after start-up, the system automatically enters STOP with Low power regulator mode and
|
|
LED2 stops toggling.
|
|
|
|
The User push-button can be pressed at any time to wake-up the system.
|
|
The software then comes back in RUN mode for 5 sec. before automatically entering STOP with Low power regulator mode again.
|
|
|
|
LED2 is used to monitor the system state as follows:
|
|
- LED2 ON: configuration failed (system will go to an infinite loop)
|
|
- LED2 toggling: system in RUN mode
|
|
- LED2 off : system in STOP with Low power regulator mode
|
|
|
|
These steps are repeated in an infinite loop.
|
|
|
|
@note To measure the current consumption in STOP with Low power regulator mode, remove JP6 jumper
|
|
and connect an amperemeter to JP6 to measure IDD current.
|
|
|
|
@note This example can not be used in DEBUG mode due to the fact
|
|
that the Cortex-M4 core is no longer clocked during low power mode
|
|
so debugging features are disabled.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
Power, PWR, Stop mode, Interrupt, EXTI, Wakeup, Low Power, External reset,
|
|
|
|
@par Directory contents
|
|
|
|
- Examples_MIX/PWR/PWR_STOP/Inc/stm32f4xx_conf.h HAL Configuration file
|
|
- Examples_MIX/PWR/PWR_STOP/Inc/stm32f4xx_it.h Header for stm32f4xx_it.c
|
|
- Examples_MIX/PWR/PWR_STOP/Inc/main.h Header file for main.c
|
|
- Examples_MIX/PWR/PWR_STOP/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
|
|
- Examples_MIX/PWR/PWR_STOP/Src/stm32f4xx_it.c Interrupt handlers
|
|
- Examples_MIX/PWR/PWR_STOP/Src/main.c Main program
|
|
- Examples_MIX/PWR/PWR_STOP/Src/stm32f4xx_hal_msp.c HAL MSP module
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F4xx devices
|
|
|
|
|
|
- This example has been tested with STMicroelectronics NUCLEO-F411RE
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- NUCLEO-F411RE set-up:
|
|
- LED2 connected to PA.05 pin
|
|
- User push-button connected to pin PC.13 (EXTI13)
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|