STM32CubeF4

/**
  @page FatFs_uSD_RTOS   FatFs with uSD card drive in RTOS mode application
 
  @verbatim
  ******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
  * @file    readme.txt
  * @author  MCD Application Team
  * @brief   Description of the FatFs with uSD card drive in RTOS mode application
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright © 2017 STMicroelectronics International N.V. 
  * All rights reserved.</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without 
  * modification, are permitted, provided that the following conditions are met:
  *
  * 1. Redistribution of source code must retain the above copyright notice, 
  *    this list of conditions and the following disclaimer.
  * 2. Redistributions in binary form must reproduce the above copyright notice,
  *    this list of conditions and the following disclaimer in the documentation
  *    and/or other materials provided with the distribution.
  * 3. Neither the name of STMicroelectronics nor the names of other 
  *    contributors to this software may be used to endorse or promote products 
  *    derived from this software without specific written permission.
  * 4. This software, including modifications and/or derivative works of this 
  *    software, must execute solely and exclusively on microcontroller or
  *    microprocessor devices manufactured by or for STMicroelectronics.
  * 5. Redistribution and use of this software other than as permitted under 
  *    this license is void and will automatically terminate your rights under 
  *    this license. 
  *
  * THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND CONTRIBUTORS "AS IS" 
  * AND ANY EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT 
  * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A 
  * PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY
  * RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT 
  * SHALL STMICROELECTRONICS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
  * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
  * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, 
  * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF 
  * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 
  * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
  * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  @endverbatim

@par Application Description

How to use STM32Cube firmware with FatFs middleware component as a generic FAT
file system module. This example develops an application exploiting FatFs
features with a microSD drive in RTOS mode configuration.

At the beginning of the main program the HAL_Init() function is called to reset 
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system clock
(SYSCLK) to run at 100 MHz.
 
The application is based on writing and reading back a text file from a drive,
it creates a normal priority thread and it's performed using FatFs APIs to 
access the FAT volume as described in the following steps: 

 - Link the uSD disk I/O driver;
 - Register the file system object (mount) to the FatFs module for the uSD drive;
 - Create a FAT file system (format) on the uSD drive;
 - Create and Open new text file object with write access;
 - Write data to the text file;
 - Close the open text file;
 - Open text file object with read access;
 - Read back data from the text file;
 - Check on read data from text file;
 - Close the open text file;
 - Unlink the uSD disk I/O driver.

Notice that the application manages possible errors that might occur during the 
access to FAT volume, when using FatFs APIs. In addition, user can check if the
written text file is available on the uSD card.

It is possible to fine tune needed FatFs features by modifying defines values 
in FatFs configuration file “ffconf.h” available under the project includes 
directory, in a way to fit the application requirements. 

STM32 board's LEDs can be used to monitor the application status:
  - LED1 is ON when the application runs successfully.
  - LED3 is ON when any error occurs.


@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
      based on variable incremented in HAL time base ISR. This implies that if HAL_Delay() is called from
      a peripheral ISR process, then the HAL time base interrupt must have higher priority (numerically lower)
      than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
      To change the HAL time base interrupt priority you have to use HAL_NVIC_SetPriority() function.
      
@note The application need to ensure that the HAL time base is always set to 1 millisecond
      to have correct HAL operation.

@note The FreeRTOS heap size configTOTAL_HEAP_SIZE defined in FreeRTOSConfig.h is set accordingly to the 
      OS resources memory requirements of the application with +10% margin and rounded to the upper Kbyte boundary.

For more details about FreeRTOS implementation on STM32Cube, please refer to UM1722 "Developing Applications 
on STM32Cube with RTOS".


@par Directory contents
 
  - FatFs/FatFs_uSD_RTOS/Inc/stm32f4xx_hal_conf.h          HAL configuration file
  - FatFs/FatFs_uSD_RTOS/Inc/stm32f4xx_it.h                Interrupt handlers header file
  - FatFs/FatFs_uSD_RTOS/Inc/main.h                        Header for main.c module
  - FatFs/FatFs_uSD_RTOS/Inc/sd_diskio.h                   FatFS sd diskio driver header file
  - FatFs/FatFs_uSD_RTOS/Inc/ffconf.h                      FAT file system module configuration file
  - FatFs/FatFs_uSD_RTOS/Inc/FreeRTOSConfig.h              FreeRTOS configuration file
  - FatFs/FatFs_uSD_RTOS/Src/stm32f4xx_it.c                Interrupt handlers
  - FatFs/FatFs_uSD_RTOS/Src/main.c                        Main program
  - FatFs/FatFs_uSD_RTOS/Src/sd_diskio.c                   FatFS sd diskio driver implementation
  - FatFs/FatFs_uSD_RTOS/Src/system_stm32f4xx.c            STM32F4xx system source file
  - FatFs/FatFs_uSD_RTOS/Src/stm32f4xx_hal_timebase_tim.c  HAL time base based on the hardware

@par Hardware and Software environment

  - This application runs on STM32F412xG devices
  - This application has been tested with STM32412G-DISCOVERY board and can be
    easily tailored to any other supported device and development board.

  - STM32F412G-Discovery Set-up
    - Connect the STM32F412G-Discovery board to the PC through 'USB micro A-Male 
      to A-Male' cable to the connector
    - Connect a uSD Card to the MSD connector (CN13).
    - Please ensure that jumpers JP5 is fitted in position 1-2

@par How to use it ? 

In order to make the program work, you must do the following:
 - Open your preferred toolchain 
 - Rebuild all files and load your image into target memory
 - Run the application

 * <h3><center>&copy; COPYRIGHT STMicroelectronics</center></h3>
 */