mirror of
https://github.com/STMicroelectronics/STM32CubeF4.git
synced 2025-05-10 19:29:12 +08:00
128 lines
6.0 KiB
Plaintext
128 lines
6.0 KiB
Plaintext
/**
|
|
@page TIM_6Steps TIM 6 Steps example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file Examples_MIX/TIM/TIM_6Steps/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TIM 6 Steps example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example shows how to configure the TIM1 peripheral to generate 6 Steps PWM
|
|
signal. The STM32F4xx TIM1 peripheral allows programming in advance the configuration
|
|
for the next TIM1 output behavior (or step) and changing the configuration of all the
|
|
channels simultaneously. This operation is possible when the COM (commutation) event
|
|
is used. This example is based on the STM32F4xx TIM HAL and LL API (LL API usage for
|
|
performance improvement).
|
|
|
|
The COM event can be generated by software by setting the COM bit in the TIM1_EGR
|
|
register or by hardware (on TRC rising edge).
|
|
In this example, a software COM event is generated each 1 ms: using the SysTick
|
|
interrupt.
|
|
|
|
The TIM1 is configured in Timing Mode, each time a COM event occurs, a new TIM1
|
|
configuration will be set in advance. Only changed states are programmed.
|
|
|
|
The break Polarity is used at High level.
|
|
|
|
The following Table describes the TIM1 Channels states:
|
|
|
|
@verbatim
|
|
-----------------------------------------------
|
|
| Step1 | Step2 | Step3 | Step4 | Step5 | Step6 |
|
|
----------------------------------------------------------
|
|
|Channel1 | 1(PWM)| 0 | 0 | 0 | 0 |1(PWM) |
|
|
----------------------------------------------------------
|
|
|Channel1N | 0 | 0 |1(PWM) |1(PWM) | 0 | 0 |
|
|
----------------------------------------------------------
|
|
|Channel2 | 0 | 0 | 0 |1(PWM) |1(PWM) | 0 |
|
|
----------------------------------------------------------
|
|
|Channel2N |1(PWM) |1(PWM) | 0 | 0 | 0 | 0 |
|
|
----------------------------------------------------------
|
|
|Channel3 | 0 |1(PWM) |1(PWM) | 0 | 0 | 0 |
|
|
----------------------------------------------------------
|
|
|Channel3N | 0 | 0 | 0 | 0 |1(PWM) |1(PWM) |
|
|
-----------------------------------------------------------
|
|
|
|
|
|
|
|
. Step1 . Step2 . Step3 . Step4 . Step 5 . Step 6 . Step1 . Step2 . Step 3 . Step 4 . Step5 ...
|
|
|
|
Channel1 (PA.08) |||||||||_________________________________|||||||||||||||||____________________________________
|
|
Channel1N (PA.07) ________________|||||||||||||||||__________________________________||||||||||||||||||__________
|
|
|
|
Channel2 (PA.09) ________________________||||||||||||||||||_________________________________|||||||||||||||||___
|
|
Channel2N (PB.00) |||||||||||||||||_________________________________|||||||||||||||||____________________________
|
|
|
|
Channel3 (PA.10) ________|||||||||||||||||__________________________________||||||||||||||||||___________________
|
|
Channel3N (PB.01) _________________________________||||||||||||||||||__________________________________|||||||||||
|
|
|
|
@endverbatim
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
Timers, 6 steps, PWM, Duty Cycle, Waveform, Oscilloscope, Output, Signal, commutation, timing mode
|
|
|
|
@par Directory contents
|
|
|
|
- Examples_MIX/TIM/TIM_6Steps/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- Examples_MIX/TIM/TIM_6Steps/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- Examples_MIX/TIM/TIM_6Steps/Inc/main.h Header for main.c module
|
|
- Examples_MIX/TIM/TIM_6Steps/Src/stm32f4xx_it.c Interrupt handlers
|
|
- Examples_MIX/TIM/TIM_6Steps/Src/main.c Main program
|
|
- Examples_MIX/TIM/TIM_6Steps/Src/system_stm32f4xx.c STM32F4xx system source file
|
|
- Examples_MIX/TIM/TIM_6Steps/Src/stm32f4xx_hal_msp.c HAL MSP file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F411xx devices.
|
|
|
|
- This example has been tested with NUCLEO-F411RE board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- NUCLEO-F411RE Set-up
|
|
- Connect the TIM1 pins to an oscilloscope to monitor the different waveforms:
|
|
- TIM1_CH1 PA.08: connected to pin 8 of CN9 connector
|
|
- TIM1_CH1N PA.07: connected to pin 4 of CN5 connector
|
|
- TIM1_CH2 PA.09: connected to pin 1 of CN5 connector
|
|
- TIM1_CH2N PB.00: connected to pin 4 of CN8 connector
|
|
- TIM1_CH3 PA.10: connected to pin 3 of CN9 connector
|
|
- TIM1_CH3N PB.01: connected to pin 24 of CN10 connector
|
|
|
|
- Connect the TIM1 break to the GND. To generate a break event, switch this
|
|
pin level from 0V to 3.3V.
|
|
- TIM1_BKIN PA.06: connected to pin 5 of CN5 connector
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|