mirror of
https://github.com/STMicroelectronics/STM32CubeF4.git
synced 2025-05-02 22:17:06 +08:00
100 lines
4.4 KiB
Plaintext
100 lines
4.4 KiB
Plaintext
/**
|
||
@page FMC_SRAM_PreInitConfig FMC PSRAM PreInit Config example
|
||
|
||
@verbatim
|
||
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
||
* @file FMC/FMC_PSRAM_PreInitConfig/readme.txt
|
||
* @author MCD Application Team
|
||
* @brief Description of the code execution from FMC PSRAM memory example.
|
||
******************************************************************************
|
||
*
|
||
* Copyright (c) 2017 STMicroelectronics. All rights reserved.
|
||
*
|
||
* This software component is licensed by ST under BSD 3-Clause license,
|
||
* the "License"; You may not use this file except in compliance with the
|
||
* License. You may obtain a copy of the License at:
|
||
* opensource.org/licenses/BSD-3-Clause
|
||
*
|
||
******************************************************************************
|
||
@endverbatim
|
||
|
||
@par Example Description
|
||
|
||
This example describes how to execute a part of the code from the PSRAM external memory.
|
||
To do this, a section is created where the function is stored.
|
||
|
||
The PSRAM is configured before to call main() function and the memory is then available
|
||
after the system reset.
|
||
|
||
The configuration of the PSRAM is done in the file system_stm32f4xx.c file in the
|
||
function SystemInit_ExtMemCtl(). It is called by the function SystemInit(), which
|
||
is the first function called by the Reset_Handler.
|
||
|
||
The code in executed in a forever loop. It is a LEDs toggling example, with some
|
||
code mapped in the PSRAM and other in Flash, to show the jump from one memory
|
||
to the other.
|
||
|
||
When a power-off is performed, the PSRAM memory content is corrupted.
|
||
|
||
LED3, and LED4 toggle in this forever loop.
|
||
|
||
In this example, HCLK is configured at 100 MHz.
|
||
The configuration of the Clock is done in the system_stm32f4xx.c by calling SetSysClk().
|
||
A specefic flashloader is required for the programming of the PSRAM memory.
|
||
|
||
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
||
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
||
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
||
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
||
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
||
|
||
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
||
to have correct HAL operation.
|
||
|
||
@par Keywords
|
||
|
||
Memory, FMC, PSRAM, PreInit, Execute, Initialization, Access
|
||
|
||
@par Directory contents
|
||
|
||
- FMC/FMC_PSRAM_PreInitConfig/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
||
- FMC/FMC_PSRAM_PreInitConfig/Inc/stm32f4xx_it.h Interrupt handlers header file
|
||
- FMC/FMC_PSRAM_PreInitConfig/Inc/main.h Header for main.c module
|
||
- FMC/FMC_PSRAM_PreInitConfig/Src/stm32f4xx_it.c Interrupt handlers
|
||
- FMC/FMC_PSRAM_PreInitConfig/Src/main.c Main program
|
||
- FMC/FMC_PSRAM_PreInitConfig/Src/system_stm32f4xx.c STM32F4xx system source file
|
||
|
||
|
||
@par Hardware and Software environment
|
||
|
||
- This example runs on STM32F413xx/STM32F423xx devices.
|
||
|
||
- This example has been tested with STM32F413H-DISCO board and can be
|
||
easily tailored to any other supported device and development board.
|
||
|
||
- STM32F413H-DISCO Set-up :
|
||
Board is configured by default to access PSRAM external memory
|
||
|
||
- A specific region for the PSRAM memory has been added in the scatter file
|
||
(STM32F413xx/STM32F423xx for IAR toolchain,
|
||
STM32F413H-DISCO.sct for Keil toolchain and linker file for SW4STM32)
|
||
|
||
The PSRAM external flash loader is not integrated with supported toolchains, it<69>s only supported with STM32
|
||
ST-Link Utility V4.0.1
|
||
To load the example, use STM32 ST-Link Utility to program both internal Flash and external PSRAM memory:
|
||
1- Open STM32 ST-Link Utility V4.1.0, click on "External Loader" from the bar menu then check
|
||
"IS66WV51216EBLL_STM32413-DISCO" box
|
||
2- Connect the STM32F413H-DISCO board to PC with USB cable through CN2
|
||
3- Use the generated file named "STM32F413H-DISCO.hex" with STM32 ST-Link Utility
|
||
to program both internal Flash and external PSRAM memory
|
||
|
||
@par How to use it ?
|
||
|
||
In order to make the program work, you must do the following :
|
||
- Open your preferred toolchain
|
||
- Rebuild all files and load your image into target memory
|
||
- Run the example
|
||
|
||
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
||
*/
|