STM32CubeF4

/**
  @page LwIP_IAP  IAP over Ethernet 
 
  @verbatim
  ******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
  * @file    LwIP/LwIP_IAP/readme.txt 
  * @author  MCD Application Team
  * @brief   Description of the in-application programming (IAP) over 
  *          Ethernet.
  ******************************************************************************
  *
  * Copyright (c) 2017 STMicroelectronics. All rights reserved.
  *
  * This software component is licensed by ST under Ultimate Liberty license
  * SLA0044, the "License"; You may not use this file except in compliance with
  * the License. You may obtain a copy of the License at:
  *                               www.st.com/SLA0044
  *
  ******************************************************************************
   @endverbatim

@par Application Description

This application guides STM32Cube HAL API users to run In-Application Programming 
(IAP) over Ethernet. 

Two IAP options are provided: 
 - IAP using TFTP (Trivial File Transfer Protocol)
 - IAP using HTTP (Hypertext Transfer Protocol) 

User has select through compile options (in main.h file) to include one or both 
options.

User has to reset the device while Pushing TAMPER button to enter IAP mode.

If the LCD is used (#define USE_LCD in main.h), log messages will be displayed 
to inform user about ethernet cable status and the IP address value, else this 
will be ensured by LEDs:
  + LED1: ethernet cable is connected.
  + LED2: ethernet cable is not connected.
  
1- LwIP/LwIP_IAP/Binary directory contains the following binaries: 

- STM324x9I_EVAL_HTTP_Server.bin: run a http server application which can be executed to:
* provide informations about STM32F4 and LwIP stack.
* allow to control the four LEDs located in the STM324x9I_EVAL board
* show the ADC3 channel 7 analog input converted value

- STM324x9I_EVAL_Systick.bin: can be used to be transfered and executed. It toggles the 4 LEDs.

2-  The required userID and password are set, and can be modified, in the main.h file.

If a DHCP server is available, a dynamic IP address can be allocated by enabling 
the DHCP process (#define USE_DHCP in main.h)

Note: In this application the Ethernet Link ISR need the HAL time base to configure 
the Ethernet MAC, so the Ethernet Link interrupt priority must be set lower (numerically greater) 
than the HAL tick interrupt priority to ensure that the System tick increments while executing 
the Ethernet Link ISR.

Note: By default, the Ethernet Half duplex mode is not supported in the 
STM324x9I-EVAL board, for more information refer to the HAL_ETH_MspInit() 
function in the ethernetif.c file

@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
      based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
      a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
      than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
      To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
      
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
      to have correct HAL operation.
      
For more details about this application, refer to UM1709 "STM32Cube Ethernet IAP application"

@par Keywords

IAP, In-Application Programming, Ethernet, ETH, LwIP, TFTP, TCP/IP, HTTP, LCD

@par Directory contents

    - LwIP/LwIP_IAP/Inc/app_ethernet.h       header of app_ethernet.c file
    - LwIP/LwIP_IAP/Inc/ethernetif.h         header for ethernetif.c file
    - LwIP/LwIP_IAP/Inc/lcd_log_conf.h       LCD Log configuration file
    - LwIP/LwIP_IAP/Inc/main.h               Main program header file          
    - LwIP/LwIP_IAP/Inc/flash_if.h           header for flash_if.c
    - LwIP/LwIP_IAP/Inc/httpserver.h         header for httpserver.c
    - LwIP/LwIP_IAP/Inc/tftpserver.h         header for tftpserver.c
    - LwIP/LwIP_IAP/Inc/lwipopts.h           LwIP stack configuration options
    - LwIP/LwIP_IAP/Inc/fsdata.h             header for fsdata.c  
    - LwIP/LwIP_IAP/Inc/stm32f4xx_hal_conf.h Library Configuration file
    - LwIP/LwIP_IAP/Inc/stm32f4xx_it.h       Interrupt handlers header file    
    - LwIP/LwIP_IAP/Src/app_ethernet.c       Ethernet specific module
    - LwIP/LwIP_IAP/Src/main.c               Main program          
    - LwIP/LwIP_IAP/Src/flash_if.c           high level functions for flash access (erase, write)
    - LwIP/LwIP_IAP/Src/httpserver.c         IAP http server functions
    - LwIP/LwIP_IAP/Src/tftpserver.c         IAP tftpserver functions
    - LwIP/LwIP_IAP/Src/fsdata.c             ROM filesystem data (html pages)
    - LwIP/LwIP_IAP/Src/system_stm32f4xx.c   STM32F4xx system file
    - LwIP/LwIP_IAP/Src/stm32f4xx_it.c       STM32F4xx Interrupt handlers
    - LwIP/LwIP_IAP/Binary                   contains a binary image to be 
                                             loaded with the IAP code 
             
@par Hardware and Software environment  
   
  - This application runs on STM32F429x/STM32F439x Devices.
    
  - This application has been tested with the following environments:
     - STM324x9I-EVAL board
     - Http clients: Firefox Mozilla V24 or Microsoft Internet Explorer V8.
     - TFTP client and DHCP server: PC utility TFTPD32 (http://tftpd32.jounin.net/)
      
  - STM324x9I-EVAL Set-up
    - Connect the eval board to remote PC (through a crossover ethernet cable)
      or to your local network (through a straight ethernet cable)
  
  - Remote PC Set-up
    - Configure a static IP address for your remote PC 
      for example 192.168.0.11 


@par How to use it ? 

In order to make the program work, you must do the following :
 - Open your preferred toolchain 
 - Rebuild all files and load your image into target memory
 - Run the application
 
 * <h3><center>&copy; COPYRIGHT STMicroelectronics</center></h3>
 */