mirror of
https://github.com/STMicroelectronics/STM32CubeF4.git
synced 2025-05-08 19:29:40 +08:00
103 lines
4.4 KiB
Plaintext
103 lines
4.4 KiB
Plaintext
/**
|
|
@page TIM_PrescalerSelection TIM Prescaler Selection example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file TIM/TIM_PrescalerSelection/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the PWM signals generation using TIM3
|
|
******************************************************************************
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics. All rights reserved.
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example shows how to configure the TIM peripheral in PWM (Pulse Width Modulation)
|
|
mode with clock prescaler selection feature activated using __HAL_RCC_TIMCLKPRESCALER()
|
|
which allows to double the output frequency.
|
|
|
|
SystemCoreClock is set to 180 MHz for STM32F4xx Devices.
|
|
|
|
In this example TIM3 input clock (TIM3CLK) is set to 4 * APB1 clock (PCLK1), since
|
|
Timer clock prescalers selection activated (TIMPRE bit from RCC_DCKCFGR register is set).
|
|
TIM3CLK = 4 * PCLK1
|
|
PCLK1 = HCLK / 4
|
|
=> TIM3CLK = HCLK = SystemCoreClock
|
|
|
|
For TIM3CLK equal to SystemCoreClock and prescaler equal to (5 - 1), TIM3 counter clock
|
|
is computed as follows:
|
|
TIM3 counter clock = TIM3CLK / (Prescaler + 1)
|
|
= SystemCoreClock / (Prescaler + 1)
|
|
= 36MHz
|
|
|
|
For ARR equal to (1800 - 1), the TIM3 output clock is computed as follows:
|
|
TIM3 output clock = TIM3 counter clock / (ARR + 1)
|
|
= 20KHZ
|
|
|
|
The TIM3 CCR1 register value is equal to 900, so the TIM3 Channel 1 generates a
|
|
PWM signal with a frequency equal to 20 KHz and a duty cycle equal to 50%:
|
|
|
|
TIM3 Channel1 duty cycle = (TIM3_CCR1/ TIM3_ARR + 1)* 100 = 50%
|
|
|
|
|
|
The PWM waveforms can be displayed using an oscilloscope.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@note The connection of the LCD reset pin to a dedicated GPIO PK7 instead of the STM32F469 NRST pin may cause residual display on LCD with applications/examples that do not require display.
|
|
The LCD clear can be ensured by hardware through the board's power off/power on or by software calling the BSP_LCD_Reset() function.
|
|
|
|
@par Keywords
|
|
|
|
Timers, PWM, Prescaler, Duty Cycle, Waveform, Oscilloscope, Output, Signal
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_PrescalerSelection/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- TIM/TIM_PrescalerSelection/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- TIM/TIM_PrescalerSelection/Inc/main.h Header for main.c module
|
|
- TIM/TIM_PrescalerSelection/Src/stm32f4xx_it.c Interrupt handlers
|
|
- TIM/TIM_PrescalerSelection/Src/main.c Main program
|
|
- TIM/TIM_PrescalerSelection/Src/stm32f4xx_hal_msp.c HAL MSP file
|
|
- TIM/TIM_PrescalerSelection/Src/system_stm32f4xx.c STM32F4xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F469xx/STM32F479xx devices.
|
|
|
|
- This example has been tested and validated with STMicroelectronics STM32469I-EVAL RevC
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM32469I-EVAL Set-up
|
|
Connect the following pins to an oscilloscope to monitor the different waveforms:
|
|
- TIM3_CH1 : PB.04, pin 24 in CN6 connector
|
|
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|