mirror of
https://github.com/STMicroelectronics/STM32CubeF4.git
synced 2025-05-01 22:17:30 +08:00
107 lines
4.7 KiB
Plaintext
107 lines
4.7 KiB
Plaintext
/**
|
||
@page TIM_Encoder TIM Encoder example
|
||
|
||
@verbatim
|
||
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
||
* @file TIM/TIM_Encoder/readme.txt
|
||
* @author MCD Application Team
|
||
* @brief This example shows how to configure the Timer in Encoder interface
|
||
* to determinate the rotation direction.
|
||
******************************************************************************
|
||
* @attention
|
||
*
|
||
* Copyright (c) 2017 STMicroelectronics.
|
||
* All rights reserved.
|
||
*
|
||
* This software is licensed under terms that can be found in the LICENSE file
|
||
* in the root directory of this software component.
|
||
* If no LICENSE file comes with this software, it is provided AS-IS.
|
||
*
|
||
******************************************************************************
|
||
@endverbatim
|
||
|
||
@par Example Description
|
||
|
||
This example shows how to configure the TIM1 peripheral in encoder mode to
|
||
determinate the rotation direction.
|
||
|
||
|
||
------------- -------------
|
||
| |CH1:PC6 CH1:PA8 | |
|
||
| |---------------------------->| |
|
||
| TIM3 | | TIM1 |
|
||
| |CH1:PC7 CH1:PE11 | |
|
||
| Quadrature |---------------------------->| Quadrature |
|
||
| encoder | | encoder |
|
||
| emulator | | interface |
|
||
| | | |
|
||
| | | |
|
||
| | |-------------| -----------
|
||
| | | Direction |--> |uwDirection|
|
||
------------- ------------- -----------
|
||
Encoder interface example description
|
||
|
||
|
||
|
||
To emulate a quadrature encoder, TIM3 is configured in toggle mode to generate
|
||
2 quadrature signals on (PC6 and PC7) at 10KHz. Each 1s, signals change phase
|
||
(+90<39>/-90<39>) to emulate a Forward/Backward rotation.
|
||
|
||
TIM1 is configured in encoder mode interface, counting on TI1 and TI2.
|
||
The counting direction corresponds to the rotation direction of the connected
|
||
sensor (emulated by TIM3 signals).
|
||
Rotation direction can be monitored by putting "uwDirection" variable in the
|
||
Live Watch window.
|
||
When uwDirection = 0, and according to the "Counting direction versus encoder
|
||
signals" table, rotation direction is Forward.
|
||
When uwDirection = 1, and according to the "Counting direction versus encoder
|
||
signals" table, rotation direction is Backward.
|
||
|
||
|
||
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
||
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
||
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
||
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
||
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
||
|
||
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
||
to have correct HAL operation.
|
||
|
||
@par Keywords
|
||
|
||
Timer, Encoder mode, Master, Slave, Duty Cycle, rotation direction, Waveform, Oscilloscope, Output, Signal
|
||
|
||
@par Directory contents
|
||
|
||
- TIM/TIM_Encoder/Inc/stm32f4xx_conf.h Library Configuration file
|
||
- TIM/TIM_Encoder/Inc/stm32f4xx_it.h Interrupt handlers header file
|
||
- TIM/TIM_Encoder/Inc/main.h Main program header file
|
||
- TIM/TIM_Encoder/Src/stm32f4xx_it.c Interrupt handlers
|
||
- TIM/TIM_Encoder/Src/main.c Main program
|
||
- TIM/TIM_Encoder/Src/stm32f4xx_hal_msp.c HAL MSP file
|
||
- TIM/TIM_Encoder/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
|
||
|
||
|
||
@par Hardware and Software environment
|
||
|
||
- This example runs on STM32F429xx/STM32F439xx devices.
|
||
|
||
- This example has been tested with STMicroelectronics STM324x9I-EVAL RevB
|
||
evaluation boards and can be easily tailored to any other supported device and development board
|
||
|
||
- STM324x9I-EVAL RevB Set-up
|
||
- Connect PC6 (TIM3_Channel 1) to PA8 (TIM1_Channel 1).
|
||
- Connect PC7 (TIM3_Channel 2) to PE11(TIM1_Channel 2).
|
||
- Put uwDirection in the debugger live watch to detect the rotation direction
|
||
change.
|
||
|
||
@par How to use it ?
|
||
|
||
In order to make the program work, you must do the following :
|
||
- Open your preferred toolchain
|
||
- Rebuild all files and load your image into target memory
|
||
- Run the example
|
||
|
||
|
||
*/
|