mirror of
https://github.com/STMicroelectronics/STM32CubeF4.git
synced 2025-05-10 19:29:12 +08:00
116 lines
5.0 KiB
Plaintext
116 lines
5.0 KiB
Plaintext
/**
|
|
@page TIM_6steps Timers Synchronization example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file TIM/TIM_6steps/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TIM 6 Steps example.
|
|
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example shows how to configure the TIM1 peripheral to generate 6 Steps.
|
|
The STM32F446xx TIM1 peripheral offers the possibility to program in advance the
|
|
configuration for the next TIM1 outputs behaviour (step) and change the configuration
|
|
of all the channels at the same time. This operation is possible when the COM
|
|
(commutation) event is used.
|
|
|
|
The COM event can be generated by software by setting the COM bit in the TIM1_EGR
|
|
register or by hardware (on TRC rising edge).
|
|
In this example, a software COM event is generated each 1 ms: using the SysTick
|
|
interrupt.
|
|
|
|
The TIM1 is configured in Timing Mode, each time a COM event occurs, a new TIM1
|
|
configuration will be set in advance. Only changed states are programmed.
|
|
|
|
The break Polarity is used at High level.
|
|
|
|
The following Table describes the TIM1 Channels states:
|
|
|
|
@verbatim
|
|
-----------------------------------------------
|
|
| Step1 | Step2 | Step3 | Step4 | Step5 | Step6 |
|
|
----------------------------------------------------------
|
|
|Channel1 | 1(PWM)| 0 | 0 | 0 | 0 |1(PWM) |
|
|
----------------------------------------------------------
|
|
|Channel1N | 0 | 0 |1(PWM) |1(PWM) | 0 | 0 |
|
|
----------------------------------------------------------
|
|
|Channel2 | 0 | 0 | 0 |1(PWM) |1(PWM) | 0 |
|
|
----------------------------------------------------------
|
|
|Channel2N |1(PWM) |1(PWM) | 0 | 0 | 0 | 0 |
|
|
----------------------------------------------------------
|
|
|Channel3 | 0 |1(PWM) |1(PWM) | 0 | 0 | 0 |
|
|
----------------------------------------------------------
|
|
|Channel3N | 0 | 0 | 0 | 0 |1(PWM) |1(PWM) |
|
|
-----------------------------------------------------------
|
|
|
|
|
|
Channel1 (PA.08) |||||||_________________________________||||||||||||||_________________________________|||||||
|
|
Channel1N (PB.13) _______________||||||||||||||||_______________________________||||||||||||||||________________
|
|
|
|
Channel2 (PA.09) _______________________||||||||||||||||_______________________________||||||||||||||||________
|
|
Channel2N (PB.14) |||||||||||||||________________________________|||||||||||||||________________________________
|
|
|
|
Channel3 (PA.10) _______||||||||||||||||_______________________________||||||||||||||||________________________
|
|
Channel3N (PB.15) ________________________________|||||||||||||||________________________________|||||||||||||||
|
|
|
|
@endverbatim
|
|
|
|
@par Keywords
|
|
|
|
Timers, 6 steps, PWM, Duty Cycle, Waveform, Oscilloscope, Output, Signal, commutation, timing mode
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_6steps/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- TIM/TIM_6steps/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- TIM/TIM_6steps/Inc/main.h Header for main.c module
|
|
- TIM/TIM_6steps/Src/stm32f4xx_it.c Interrupt handlers
|
|
- TIM/TIM_6steps/Src/main.c Main program
|
|
- TIM/TIM_6steps/Src/stm32f4xx_hal_msp.c HAL MSP file
|
|
- TIM/TIM_6steps/Src/system_stm32f4xx.c STM32F4xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F446xx devices.
|
|
|
|
- This example has been tested with STM32446E-EVAL board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM32446E-EVAL Set-up
|
|
Connect the following pins to an oscilloscope to monitor the different waveforms:
|
|
- TIM1_CH1 pin PA.08(pin 1 in CN6 connector)
|
|
- TIM1_CH1N pin PB.13
|
|
- TIM1_CH2 pin PA.09
|
|
- TIM1_CH2N pin PB.14(Pin 7 in CN6 connector)
|
|
- TIM1_CH3 pin PA.10
|
|
- TIM1_CH3N pin PB.15(pin 5 in CN6 connector)
|
|
|
|
- Connect the TIM1 break pin TIM1_BKIN pin (PB.12) to the GND. To generate a
|
|
break event, switch this pin level from 0V to 3.3V.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files: Project->Rebuild all
|
|
- Load project image: Project->Download and Debug
|
|
- Run program: Debug->Go(F5)
|
|
|
|
|
|
*/
|