mirror of
https://github.com/STMicroelectronics/STM32CubeF4.git
synced 2025-05-01 22:17:30 +08:00
86 lines
3.6 KiB
Plaintext
86 lines
3.6 KiB
Plaintext
/**
|
|
@page ADC_RegularConversion_DMA ADC3 conversion using DMA for Data transfer
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file ADC/ADC_RegularConversion_DMA/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the ADC RegularConversion DMA example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to use the ADC3 and DMA to transfer continuously converted data from
|
|
ADC3 to memory.
|
|
|
|
The ADC3 is configured to convert continuously channel8(for STM324x9I-EVAL RevB).
|
|
|
|
Each time an end of conversion occurs the DMA transfers, in circular mode, the
|
|
converted data from ADC3 DR register to the uhADCxConvertedValue variable.
|
|
|
|
In this example, the system clock is 144MHz, APB2 = 72MHz and ADC clock = APB2/2.
|
|
Since ADC3 clock is 36 MHz and sampling time is set to 3 cycles, the conversion
|
|
time to 12bit data is 12 cycles so the total conversion time is (12+3)/36= 0.41us(2.4Msps).
|
|
|
|
User can vary the ADC3 channel8(for STM324x9I-EVAL RevB) voltage using the Eval Board potentiometer
|
|
|
|
STM32 Eval boards LEDs can be used to monitor the transfer status:
|
|
- LED1 is ON when the conversion is complete.
|
|
- LED3 is ON when there are an error in initialization.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
Analog, ADC, Analog to Digital Converter, Regular Conversion, DMA, Continuous Conversion
|
|
|
|
@par Directory contents
|
|
|
|
- ADC/ADC_RegularConversion_DMA/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- ADC/ADC_RegularConversion_DMA/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- ADC/ADC_RegularConversion_DMA/Inc/main.h Main program header file
|
|
- ADC/ADC_RegularConversion_DMA/Src/stm32f4xx_it.c Interrupt handlers
|
|
- ADC/ADC_RegularConversion_DMA/Src/main.c Main program
|
|
- ADC/ADC_RegularConversion_DMA/Src/stm32f4xx_hal_msp.c HAL MSP module
|
|
- ADC/ADC_RegularConversion_DMA/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F429xx/STM32F439xx devices.
|
|
|
|
- This example has been tested with STM324x9I-EVAL RevB evaluation board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM324x9I-EVAL RevB Set-up
|
|
- Use the Potentiometer (RV1) of the Eval board (connected to PF.10).
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|