/**
  ******************************************************************************
  * @file    Examples_LL/PWR/PWR_EnterStopMode/Src/main.c
  * @author  MCD Application Team
  * @brief   This example describes how to  enter and exit the STOP_MAINREGU mode
  *          through the STM32F4xx PWR LL API.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "main.h"

/** @addtogroup STM32F4xx_LL_Examples
  * @{
  */

/** @addtogroup PWR_EnterStopMode
  * @{
  */

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
void     SystemClock_Config(void);
void     Configure_PWR(void);
void     LED_Init(void);
void     LED_Off(void);
void     LED_Blinking_5s(void);
void     EnterSTOP_MAINREGUMode(void);
/* Private functions ---------------------------------------------------------*/

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* Configure the system clock to 100 MHz */
  SystemClock_Config();

  /* Initialize LED2 */
  LED_Init();

  /* Configure Power IP */
  Configure_PWR();

  /* Led blinking during 5s in RUN mode */
  LED_Blinking_5s();

  /* Switch OFF LED2 */
  LED_Off();

  /* Enter STOP_MAINREGU mode */
  EnterSTOP_MAINREGUMode();

  /* Here Device is in STOP_MAINREGU mode */

  /* Infinite loop */
  while (1)
  {
  }
}

/**
  * @brief  Initialize LED2.
  * @param  None
  * @retval None
  */
void LED_Init(void)
{
  /* Enable the LED2 Clock */
  LED2_GPIO_CLK_ENABLE();

  /* Configure IO in output push-pull mode to drive external LED2 */
  LL_GPIO_SetPinMode(LED2_GPIO_PORT, LED2_PIN, LL_GPIO_MODE_OUTPUT);
  /* Reset value is LL_GPIO_OUTPUT_PUSHPULL */
  //LL_GPIO_SetPinOutputType(LED2_GPIO_PORT, LED2_PIN, LL_GPIO_OUTPUT_PUSHPULL);
  /* Reset value is LL_GPIO_SPEED_FREQ_LOW */
  //LL_GPIO_SetPinSpeed(LED2_GPIO_PORT, LED2_PIN, LL_GPIO_SPEED_FREQ_LOW);
  /* Reset value is LL_GPIO_PULL_NO */
  //LL_GPIO_SetPinPull(LED2_GPIO_PORT, LED2_PIN, LL_GPIO_PULL_NO);
}

/**
  * @brief  Turn-off LED2.
  * @param  None
  * @retval None
  */
void LED_Off(void)
{
  /* Turn LED2 off */
  LL_GPIO_ResetOutputPin(LED2_GPIO_PORT, LED2_PIN);
}

/**
  * @brief  Set LED2 to Blinking mode during 5s.
  * @param  None

  * @retval None
  */
void LED_Blinking_5s(void)
{
  uint32_t i = 0;

  /* Toggle IO in during 5s (25*200ms) */
  for(i = 0; i < 25; i++)
  {
    LL_GPIO_TogglePin(LED2_GPIO_PORT, LED2_PIN);  
    LL_mDelay(200);
  }
}

/**
  * @brief  Function to configure and initialize PWR IP.
  * @param  None
  * @retval None
  */
void Configure_PWR(void)
{
  /* Enable Power Clock */
  LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_PWR);

}

/**
  * @brief  Function to configure and enter in STOP_MAINREGU Mode.
  * @param  None
  * @retval None
  */
void EnterSTOP_MAINREGUMode(void)
{
  LL_GPIO_InitTypeDef gpio_initstruct = {LL_GPIO_PIN_ALL, LL_GPIO_MODE_ANALOG, 
                                         LL_GPIO_SPEED_FREQ_HIGH, LL_GPIO_OUTPUT_PUSHPULL, 
                                         LL_GPIO_PULL_NO, LL_GPIO_AF_0};

  /* Set all GPIO in analog state to reduce power consumption,                */
  /* Note: Debug using ST-Link is not possible during the execution of this   */
  /*       example because communication between ST-link and the device       */
  /*       under test is done through UART. All GPIO pins are disabled (set   */
  /*       to analog input mode) including  UART I/O pins.                    */
  LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_GPIOA |
                           LL_AHB1_GRP1_PERIPH_GPIOB |
                           LL_AHB1_GRP1_PERIPH_GPIOC |
                           LL_AHB1_GRP1_PERIPH_GPIOD |
                           LL_AHB1_GRP1_PERIPH_GPIOE |
                           LL_AHB1_GRP1_PERIPH_GPIOH);

  LL_GPIO_Init(GPIOA, &gpio_initstruct);
  LL_GPIO_Init(GPIOB, &gpio_initstruct);
  LL_GPIO_Init(GPIOC, &gpio_initstruct);
  LL_GPIO_Init(GPIOD, &gpio_initstruct);
  LL_GPIO_Init(GPIOE, &gpio_initstruct);
  LL_GPIO_Init(GPIOH, &gpio_initstruct);

  LL_AHB1_GRP1_DisableClock(LL_AHB1_GRP1_PERIPH_GPIOA |
                           LL_AHB1_GRP1_PERIPH_GPIOB |
                           LL_AHB1_GRP1_PERIPH_GPIOC |
                           LL_AHB1_GRP1_PERIPH_GPIOD |
                           LL_AHB1_GRP1_PERIPH_GPIOE |
                           LL_AHB1_GRP1_PERIPH_GPIOH);

  /** Request to enter STOP_MAINREGU mode
    * Following procedure describe in STM32F4xx Reference Manual
    * See PWR part, section Low-power modes, STOP_MAINREGU mode
    */
  /* Set STOP_MAINREGU mode when CPU enters deepsleep */
  LL_PWR_SetPowerMode(LL_PWR_MODE_STOP_MAINREGU);

  /* Set SLEEPDEEP bit of Cortex System Control Register */
  LL_LPM_EnableDeepSleep();  

  /* Request Wait For Interrupt */
  __WFI();
}

/**
  * @brief  System Clock Configuration
  *         The system Clock is configured as follow :
  *            System Clock source            = PLL (HSE)
  *            SYSCLK(Hz)                     = 100000000
  *            HCLK(Hz)                       = 100000000
  *            AHB Prescaler                  = 1
  *            APB1 Prescaler                 = 2
  *            APB2 Prescaler                 = 1
  *            HSE Frequency(Hz)              = 8000000
  *            PLL_M                          = 8
  *            PLL_N                          = 400
  *            PLL_P                          = 4
  *            VDD(V)                         = 3.3
  *            Main regulator output voltage  = Scale1 mode
  *            Flash Latency(WS)              = 3
  * @param  None
  * @retval None
  */
void SystemClock_Config(void)
{
  /* Enable HSE oscillator */
  LL_RCC_HSE_EnableBypass();
  LL_RCC_HSE_Enable();
  while(LL_RCC_HSE_IsReady() != 1)
  {
  };

  /* Set FLASH latency */
  LL_FLASH_SetLatency(LL_FLASH_LATENCY_3);

  /* Main PLL configuration and activation */
  LL_RCC_PLL_ConfigDomain_SYS(LL_RCC_PLLSOURCE_HSE, LL_RCC_PLLM_DIV_8, 400, LL_RCC_PLLP_DIV_4);
  LL_RCC_PLL_Enable();
  while(LL_RCC_PLL_IsReady() != 1)
  {
  };

  /* Sysclk activation on the main PLL */
  LL_RCC_SetAHBPrescaler(LL_RCC_SYSCLK_DIV_1);
  LL_RCC_SetSysClkSource(LL_RCC_SYS_CLKSOURCE_PLL);
  while(LL_RCC_GetSysClkSource() != LL_RCC_SYS_CLKSOURCE_STATUS_PLL)
  {
  };

  /* Set APB1 & APB2 prescaler */
  LL_RCC_SetAPB1Prescaler(LL_RCC_APB1_DIV_2);
  LL_RCC_SetAPB2Prescaler(LL_RCC_APB2_DIV_1);

  /* Set systick to 1ms */
  SysTick_Config(100000000 / 1000);

  /* Update CMSIS variable (which can be updated also through SystemCoreClockUpdate function) */
  SystemCoreClock = 100000000;
}

#ifdef  USE_FULL_ASSERT

/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t *file, uint32_t line)
{
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d", file, line) */

  /* Infinite loop */
  while (1)
  {
  }
}
#endif
/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/