mirror of
https://github.com/STMicroelectronics/STM32CubeF3.git
synced 2025-05-03 22:17:07 +08:00
105 lines
4.9 KiB
Plaintext
105 lines
4.9 KiB
Plaintext
/**
|
|
@page TIM_TimeBase Time Base example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file TIM/TIM_TimeBase/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TIM Time Base example
|
|
******************************************************************************
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without modification,
|
|
* are permitted provided that the following conditions are met:
|
|
* 1. Redistributions of source code must retain the above copyright notice,
|
|
* this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
|
* this list of conditions and the following disclaimer in the documentation
|
|
* and/or other materials provided with the distribution.
|
|
* 3. Neither the name of STMicroelectronics nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
|
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
|
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example shows how to configure the TIM peripheral to generate a time base of
|
|
one second with the corresponding Interrupt request.
|
|
|
|
In this example TIM2 input clock (TIM2CLK) is set to 2 * APB1 clock (PCLK1),
|
|
since APB1 prescaler is different from 1.
|
|
TIM2CLK = 2 * PCLK1
|
|
PCLK1 = HCLK / 2
|
|
=> TIM2CLK = HCLK = SystemCoreClock (Hz)
|
|
To get TIM2 counter clock at 10 KHz, the Prescaler is computed as following:
|
|
Prescaler = (TIM2CLK / TIM2 counter clock) - 1
|
|
Prescaler = (SystemCoreClock /10 KHz) - 1
|
|
|
|
SystemCoreClock is set to 64 MHz for STM32F3xx Devices.
|
|
|
|
The TIM2 ARR register value is equal to 10000 - 1,
|
|
Update rate = TIM2 counter clock / (Period + 1) = 1 Hz,
|
|
So the TIM2 generates an interrupt each 1 s
|
|
|
|
When the counter value reaches the auto-reload register value, the TIM update
|
|
interrupt is generated and, in the handler routine, pin GPIOB.0 (connected to LED1 on board STM32F303ZE-Nucleo Rev B)
|
|
is toggled at the following frequency: 0.5Hz.
|
|
|
|
In case of error, LED2 is turned ON.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_TimeBase/Inc/stm32f3xx_hal_conf.h HAL configuration file
|
|
- TIM/TIM_TimeBase/Inc/stm32f3xx_it.h Interrupt handlers header file
|
|
- TIM/TIM_TimeBase/Inc/main.h Header for main.c module
|
|
- TIM/TIM_TimeBase/Src/stm32f3xx_it.c Interrupt handlers
|
|
- TIM/TIM_TimeBase/Src/main.c Main program
|
|
- TIM/TIM_TimeBase/Src/stm32f3xx_hal_msp.c HAL MSP file
|
|
- TIM/TIM_TimeBase/Src/system_stm32f3xx.c STM32F3xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F303ZE devices.
|
|
- In this example, the clock is set to 64 MHz.
|
|
|
|
- This example has been tested with STMicroelectronics STM32F303ZE-Nucleo Rev B
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM32F303ZE-Nucleo Rev B Set-up
|
|
- Use LED1 connected to GPIOB.0 pin (connected to pin 31 on CN10 Connector) and connect it on an oscilloscope
|
|
to show the Time Base signal.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|