STM32CubeF3

@verbatim
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
* @file TIM/TIM_InputCapture/readme.txt
* @author MCD Application Team
* @brief Description of the TIM_InputCapture example.
******************************************************************************
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
@endverbatim

@par Example Description

This example shows how to use the TIM peripheral to measure the frequency of
an external signal.

The TIM15CLK frequency is set to SystemCoreClock (Hz), the Prescaler is 0,
so the TIM15 counter clock is SystemCoreClock (Hz).
SystemCoreClock is set to 64 MHz for STM32F303ZE Devices.

TIM15 is configured in Input Capture Mode: the external signal is connected to
TIM15 Channel2 used as input pin.
To measure the frequency we use the TIM15 CC2 interrupt request, so in the
TIM15_IRQHandler routine, the frequency of the external signal is computed.

The "uwFrequency" variable contains the external signal frequency:
uwFrequency = TIM15 counter clock / uwDiffCapture (Hz),
where "uwDiffCapture" is the difference between two consecutive TIM15 captures.

The minimum frequency value to measure is TIM15 counter clock / CCR MAX
= 64 MHz / 65535

Due to TIM15_IRQHandler processing time (around 3.50us), the maximum
frequency value to measure is around 300kHz.

@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.

@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.

@par Directory contents

- TIM/TIM_InputCapture/Inc/stm32f3xx_hal_conf.h HAL configuration file
- TIM/TIM_InputCapture/Inc/stm32f3xx_it.h Interrupt handlers header file
- TIM/TIM_InputCapture/Inc/main.h Header for main.c module
- TIM/TIM_InputCapture/Src/stm32f3xx_it.c Interrupt handlers
- TIM/TIM_InputCapture/Src/main.c Main program
- TIM/TIM_InputCapture/Src/stm32f3xx_hal_msp.c HAL MSP file
- TIM/TIM_InputCapture/Src/system_stm32f3xx.c STM32F3xx system source file

@par Hardware and Software environment

- This example runs on STM32F303ZE devices.
- In this example, the clock is set to 64 MHz.

- This example has been tested with STMicroelectronics STM32F303ZE-Nucleo Rev B
board and can be easily tailored to any other supported device
and development board.

- STM32F303ZE-Nucleo Rev B Set-up
- Connect the external signal to measure to the TIM15 CH2 pin (PA.03 (Arduino A0 - connected to pin 1 on CN9 Connector)).

@par How to use it ?

In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example