STM32CubeF3

@verbatim
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
* @file SDADC/SDADC_TempMeasurement/readme.txt
* @author MCD Application Team
* @brief Description of the SDADC Temperature measurement using PT100 sensor.
******************************************************************************
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
@endverbatim

@par Example Description

This example aims to show how to use the 16-bit resolution Sigma-Delta
Analog-to-Digital converter to perform accurate temperature measurement.

This is done using the PT100 sensor connected to PE7 in the STM32373C-EVAL evaluation board.

- The SDADC is configured in single ended offset. The input range is from 0V to VREF/(2*gain).
In this example, the SDADC internal gain is set to 8 so the range is from 0V to VREF/16.
The external reference VREF (set to 3.3V on STM32373C-EVAL) is used as reference for SDADC
using JP17 so the measurement ranges between 0V and VREF/16 = 0,20625V.
The conversion is performed in continuous mode with interrupt enabled on end
of regular conversion.
A PT-100 sensor is connected to SDADC1 channel 3P (PE7) through a reference
resistor 1K8 labeled R33 on STM32373C-EVAL evaluation board.
The temperature is computed using the formula below:
Rpt100 = 100 + 0.385 * T ==> T = (Rpt100 - 100) / 0.385
Vpt100 = Rpt100 * Ipt100 = Rpt100 * VDD_ANA / 2 * Rref ==> Rpt100 = Vpt100 * 1800 * 2 / VDD_ANA
==> T = ((Vpt100 * 1800 * 2 / VDD_ANA) - 100) / 0.385
= ((SDADC_Sample * 1800 * 2 / 65535) - 100) / 0.385
with:
- Rpt100 is the resistance of the PT100 sensor
- Vpt100 is the voltage measured on PT100 sensor
- Ipt100 is the current crossing the PT100 sensor
- VDD_ANA is the analog voltage
- Rref is the reference resistor 1K8 labeled R33 on STM32373C-EVAL
- SDADC_Sample is the digital value read from SDADC data register

- The temperature measurement is performed in two steps:
1. Temperature sensor calibration: this phase is performed with JP18
fitted in 2-3(REF)position. A 100 Ohm resistor is connected to PE7 which is
connected to VREF through the reference resistor.
The SDADC converter measures the analog voltage applied on PE7 and then
computes the correction coefficient.
The PT100 is not connected in this phase.
2. The temperature measurement: this phase is performed with JP18
fitted in 1-2(PT100) position. The PT100 sensor is connected to PE7 which is
connected to VREF through the reference resistor.
The SDADC converter measures the analog voltage applied on PE7 and then
computes the temperature which is given by the following formula:
TemperaturePT100 = (((((CoeffCorrection * (AvrgRegularConvData/SDADC_GAIN) * REFERENCE_RESISTOR * 2) / SDADCRESOL) - RESISTANCE_ZERODEGRE) / RESISTANCE_COEFFICIENT);
with:
- AvrgRegularConvData is the average value of 256 samples
- SDADC_GAIN is the internal SDADC gain. In this example it is set to 8
- CoeffCorrection is the correction coefficient computed in phase 1.
- REFERENCE_RESISTOR is the reference resistor 1K8 labeled R33 on STM32373C-EVAL
- SDADCRESOL is the sigma delta converter resolution: 2e16-1
- RESISTANCE_ZERODEGRE is the resistance of PT100 at 0 degree C
- RESISTANCE_COEFFICIENT is the coefficient of PT100 sensor

- The measured temperature is displayed on the LCD mounted on STM32373C-EVAL.

@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.

@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.

@par Directory contents

- SDADC/SDADC_TempMeasurement/Inc/stm32f3xx_hal_conf.h HAL configuration file
- SDADC/SDADC_TempMeasurement/Inc/stm32f3xx_it.h Interrupt handlers header file
- SDADC/SDADC_TempMeasurement/Inc/main.h Header for main.c module
- SDADC/SDADC_TempMeasurement/Src/stm32f3xx_it.c Interrupt handlers
- SDADC/SDADC_TempMeasurement/Src/stm32f3xx_hal_msp.c.c HAL MSP module
- SDADC/SDADC_TempMeasurement/Src/main.c Main program
- SDADC/SDADC_TempMeasurement/Src/system_stm32f3xx.c STM32F3xx system source file

@par Hardware and Software environment

- This example runs on STM32F373xC devices.

- This example has been tested with STMicroelectronics STM32373C-EVAL RevB
boards and can be easily tailored to any other supported device
and development board.

- STM32373xC-EVAL Set-up
- Make sure that jumper JP16 and JP17 are fitted.
- Make sure that the jumper JP12 and JP13 are fitted in 3V3 position.
- Follow example instructions on jumper JP18 position

@par How to use it ?

In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example