mirror of
https://github.com/STMicroelectronics/STM32CubeF3.git
synced 2025-05-01 22:18:23 +08:00
105 lines
4.4 KiB
Plaintext
105 lines
4.4 KiB
Plaintext
/**
|
|
@page TIM_ComplementarySignals TIM Complementary Signals example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file TIM/TIM_ComplementarySignals/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TIM Complementary Signals example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Configuration of the TIM1 peripheral to generate three
|
|
complementary signals, insert a predefined deadtime value, use the break
|
|
feature, and lock the break and dead-time configuration.
|
|
|
|
This is done using TIM15 peripheral.
|
|
|
|
TIM15CLK is fixed to SystemCoreClock, the TIM15 Prescaler is set to have
|
|
TIM15 counter clock = 18MHz.
|
|
|
|
The objective is to generate PWM signal at 10 KHz:
|
|
- TIM15_Period = (SystemCoreClock / 10000) - 1
|
|
|
|
Duty cycle is computed as the following description:
|
|
The channel 1 duty cycle is set to 50% so channel 1N is set to 50%.
|
|
The Timer pulse is calculated as follows:
|
|
- Channel1Pulse = DutyCycle * (TIM15_Period - 1) / 100
|
|
|
|
A dead time equal to 100/SystemCoreClock (around 1.4us) is inserted between
|
|
the different complementary signals, and the Lock level 1 is selected.
|
|
- The OCx output signal is the same as the reference signal except for the rising edge,
|
|
which is delayed relative to the reference rising edge.
|
|
- The OCxN output signal is the opposite of the reference signal except for the rising
|
|
edge, which is delayed relative to the reference falling edge
|
|
|
|
Note that calculated duty cycles apply to the reference signal (OCxREF) from
|
|
which outputs OCx and OCxN are generated. As dead time insertion is enabled the
|
|
duty cycle measured on OCx will be slightly lower.
|
|
|
|
The break Polarity is used at High level.
|
|
|
|
The TIM15 waveforms can be displayed using an oscilloscope.
|
|
|
|
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_ComplementarySignals/Src/main.c Main program
|
|
- TIM/TIM_ComplementarySignals/Src/system_stm32f3xx.c STM32F3xx system clock configuration file
|
|
- TIM/TIM_ComplementarySignals/Src/stm32f3xx_it.c Interrupt handlers
|
|
- TIM/TIM_ComplementarySignals/Src/stm32f3xx_hal_msp.c HAL MSP module
|
|
- TIM/TIM_ComplementarySignals/Inc/main.h Main program header file
|
|
- TIM/TIM_ComplementarySignals/Inc/stm32f3xx_hal_conf.h HAL Configuration file
|
|
- TIM/TIM_ComplementarySignals/Inc/stm32f3xx_it.h Interrupt handlers header file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F373xC devices.
|
|
|
|
- This example has been tested with STMicroelectronics STM32373C-EVAL RevB
|
|
boards and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM32373C-EVAL RevB Set-up
|
|
- Connect the TIM15 pins to an oscilloscope to monitor the different waveforms:
|
|
- TIM15_CH1 pin (PA.02)
|
|
- TIM15_CH1N pin (PA.01)
|
|
|
|
- Connect the TIM15 break pin TIM15_BKIN pin (PA.09) to the GND. To generate a
|
|
break event, switch this pin level from 0V to 3.3V.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|