diff --git a/Drivers/STM32F2xx_HAL_Driver/Src/stm32f2xx_hal_tim_ex.c b/Drivers/STM32F2xx_HAL_Driver/Src/stm32f2xx_hal_tim_ex.c index 9ae55961..29f402fb 100644 --- a/Drivers/STM32F2xx_HAL_Driver/Src/stm32f2xx_hal_tim_ex.c +++ b/Drivers/STM32F2xx_HAL_Driver/Src/stm32f2xx_hal_tim_ex.c @@ -1,1945 +1,1108 @@ /** ****************************************************************************** - * @file stm32f2xx_hal_tim_ex.c + * @file stm32f2xx_ll_sdmmc.h * @author MCD Application Team - * @brief TIM HAL module driver. - * This file provides firmware functions to manage the following - * functionalities of the Timer Extended peripheral: - * + Time Hall Sensor Interface Initialization - * + Time Hall Sensor Interface Start - * + Time Complementary signal break and dead time configuration - * + Time Master and Slave synchronization configuration - * + Timer remapping capabilities configuration - @verbatim - ============================================================================== - ##### TIMER Extended features ##### - ============================================================================== - [..] - The Timer Extended features include: - (#) Complementary outputs with programmable dead-time for : - (++) Output Compare - (++) PWM generation (Edge and Center-aligned Mode) - (++) One-pulse mode output - (#) Synchronization circuit to control the timer with external signals and to - interconnect several timers together. - (#) Break input to put the timer output signals in reset state or in a known state. - (#) Supports incremental (quadrature) encoder and hall-sensor circuitry for - positioning purposes - - ##### How to use this driver ##### - ============================================================================== - [..] - (#) Initialize the TIM low level resources by implementing the following functions - depending on the selected feature: - (++) Hall Sensor output : HAL_TIMEx_HallSensor_MspInit() - - (#) Initialize the TIM low level resources : - (##) Enable the TIM interface clock using __HAL_RCC_TIMx_CLK_ENABLE(); - (##) TIM pins configuration - (+++) Enable the clock for the TIM GPIOs using the following function: - __HAL_RCC_GPIOx_CLK_ENABLE(); - (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init(); - - (#) The external Clock can be configured, if needed (the default clock is the - internal clock from the APBx), using the following function: - HAL_TIM_ConfigClockSource, the clock configuration should be done before - any start function. - - (#) Configure the TIM in the desired functioning mode using one of the - initialization function of this driver: - (++) HAL_TIMEx_HallSensor_Init() and HAL_TIMEx_ConfigCommutEvent(): to use the - Timer Hall Sensor Interface and the commutation event with the corresponding - Interrupt and DMA request if needed (Note that One Timer is used to interface - with the Hall sensor Interface and another Timer should be used to use - the commutation event). - - (#) Activate the TIM peripheral using one of the start functions: - (++) Complementary Output Compare : HAL_TIMEx_OCN_Start(), HAL_TIMEx_OCN_Start_DMA(), HAL_TIMEx_OC_Start_IT() - (++) Complementary PWM generation : HAL_TIMEx_PWMN_Start(), HAL_TIMEx_PWMN_Start_DMA(), HAL_TIMEx_PWMN_Start_IT() - (++) Complementary One-pulse mode output : HAL_TIMEx_OnePulseN_Start(), HAL_TIMEx_OnePulseN_Start_IT() - (++) Hall Sensor output : HAL_TIMEx_HallSensor_Start(), HAL_TIMEx_HallSensor_Start_DMA(), HAL_TIMEx_HallSensor_Start_IT(). - - @endverbatim + * @brief Header file of SDMMC HAL module. ****************************************************************************** * @attention * - *

© Copyright (c) 2016 STMicroelectronics. + *

© Copyright (c) 2018 STMicroelectronics. * All rights reserved.

* * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the * License. You may obtain a copy of the License at: - * opensource.org/licenses/BSD-3-Clause + * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** - */ + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef STM32F2xx_LL_SDMMC_H +#define STM32F2xx_LL_SDMMC_H + +#ifdef __cplusplus + extern "C" { +#endif /* Includes ------------------------------------------------------------------*/ -#include "stm32f2xx_hal.h" +#include "stm32f2xx_hal_def.h" -/** @addtogroup STM32F2xx_HAL_Driver +/** @addtogroup STM32F2xx_Driver * @{ */ -/** @defgroup TIMEx TIMEx - * @brief TIM Extended HAL module driver +/** @addtogroup SDMMC_LL + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup SDMMC_LL_Exported_Types SDMMC_LL Exported Types + * @{ + */ + +/** + * @brief SDMMC Configuration Structure definition + */ +typedef struct +{ + uint32_t ClockEdge; /*!< Specifies the clock transition on which the bit capture is made. + This parameter can be a value of @ref SDMMC_LL_Clock_Edge */ + + uint32_t ClockBypass; /*!< Specifies whether the SDMMC Clock divider bypass is + enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_Clock_Bypass */ + + uint32_t ClockPowerSave; /*!< Specifies whether SDMMC Clock output is enabled or + disabled when the bus is idle. + This parameter can be a value of @ref SDMMC_LL_Clock_Power_Save */ + + uint32_t BusWide; /*!< Specifies the SDMMC bus width. + This parameter can be a value of @ref SDMMC_LL_Bus_Wide */ + + uint32_t HardwareFlowControl; /*!< Specifies whether the SDMMC hardware flow control is enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_Hardware_Flow_Control */ + + uint32_t ClockDiv; /*!< Specifies the clock frequency of the SDMMC controller. + This parameter can be a value between Min_Data = 0 and Max_Data = 255 */ + +}SDIO_InitTypeDef; + + +/** + * @brief SDMMC Command Control structure + */ +typedef struct +{ + uint32_t Argument; /*!< Specifies the SDMMC command argument which is sent + to a card as part of a command message. If a command + contains an argument, it must be loaded into this register + before writing the command to the command register. */ + + uint32_t CmdIndex; /*!< Specifies the SDMMC command index. It must be Min_Data = 0 and + Max_Data = 64 */ + + uint32_t Response; /*!< Specifies the SDMMC response type. + This parameter can be a value of @ref SDMMC_LL_Response_Type */ + + uint32_t WaitForInterrupt; /*!< Specifies whether SDMMC wait for interrupt request is + enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_Wait_Interrupt_State */ + + uint32_t CPSM; /*!< Specifies whether SDMMC Command path state machine (CPSM) + is enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_CPSM_State */ +}SDIO_CmdInitTypeDef; + + +/** + * @brief SDMMC Data Control structure + */ +typedef struct +{ + uint32_t DataTimeOut; /*!< Specifies the data timeout period in card bus clock periods. */ + + uint32_t DataLength; /*!< Specifies the number of data bytes to be transferred. */ + + uint32_t DataBlockSize; /*!< Specifies the data block size for block transfer. + This parameter can be a value of @ref SDMMC_LL_Data_Block_Size */ + + uint32_t TransferDir; /*!< Specifies the data transfer direction, whether the transfer + is a read or write. + This parameter can be a value of @ref SDMMC_LL_Transfer_Direction */ + + uint32_t TransferMode; /*!< Specifies whether data transfer is in stream or block mode. + This parameter can be a value of @ref SDMMC_LL_Transfer_Type */ + + uint32_t DPSM; /*!< Specifies whether SDMMC Data path state machine (DPSM) + is enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_DPSM_State */ +}SDIO_DataInitTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup SDMMC_LL_Exported_Constants SDMMC_LL Exported Constants + * @{ + */ +#define SDMMC_ERROR_NONE ((uint32_t)0x00000000U) /*!< No error */ +#define SDMMC_ERROR_CMD_CRC_FAIL ((uint32_t)0x00000001U) /*!< Command response received (but CRC check failed) */ +#define SDMMC_ERROR_DATA_CRC_FAIL ((uint32_t)0x00000002U) /*!< Data block sent/received (CRC check failed) */ +#define SDMMC_ERROR_CMD_RSP_TIMEOUT ((uint32_t)0x00000004U) /*!< Command response timeout */ +#define SDMMC_ERROR_DATA_TIMEOUT ((uint32_t)0x00000008U) /*!< Data timeout */ +#define SDMMC_ERROR_TX_UNDERRUN ((uint32_t)0x00000010U) /*!< Transmit FIFO underrun */ +#define SDMMC_ERROR_RX_OVERRUN ((uint32_t)0x00000020U) /*!< Receive FIFO overrun */ +#define SDMMC_ERROR_ADDR_MISALIGNED ((uint32_t)0x00000040U) /*!< Misaligned address */ +#define SDMMC_ERROR_BLOCK_LEN_ERR ((uint32_t)0x00000080U) /*!< Transferred block length is not allowed for the card or the + number of transferred bytes does not match the block length */ +#define SDMMC_ERROR_ERASE_SEQ_ERR ((uint32_t)0x00000100U) /*!< An error in the sequence of erase command occurs */ +#define SDMMC_ERROR_BAD_ERASE_PARAM ((uint32_t)0x00000200U) /*!< An invalid selection for erase groups */ +#define SDMMC_ERROR_WRITE_PROT_VIOLATION ((uint32_t)0x00000400U) /*!< Attempt to program a write protect block */ +#define SDMMC_ERROR_LOCK_UNLOCK_FAILED ((uint32_t)0x00000800U) /*!< Sequence or password error has been detected in unlock + command or if there was an attempt to access a locked card */ +#define SDMMC_ERROR_COM_CRC_FAILED ((uint32_t)0x00001000U) /*!< CRC check of the previous command failed */ +#define SDMMC_ERROR_ILLEGAL_CMD ((uint32_t)0x00002000U) /*!< Command is not legal for the card state */ +#define SDMMC_ERROR_CARD_ECC_FAILED ((uint32_t)0x00004000U) /*!< Card internal ECC was applied but failed to correct the data */ +#define SDMMC_ERROR_CC_ERR ((uint32_t)0x00008000U) /*!< Internal card controller error */ +#define SDMMC_ERROR_GENERAL_UNKNOWN_ERR ((uint32_t)0x00010000U) /*!< General or unknown error */ +#define SDMMC_ERROR_STREAM_READ_UNDERRUN ((uint32_t)0x00020000U) /*!< The card could not sustain data reading in stream rmode */ +#define SDMMC_ERROR_STREAM_WRITE_OVERRUN ((uint32_t)0x00040000U) /*!< The card could not sustain data programming in stream mode */ +#define SDMMC_ERROR_CID_CSD_OVERWRITE ((uint32_t)0x00080000U) /*!< CID/CSD overwrite error */ +#define SDMMC_ERROR_WP_ERASE_SKIP ((uint32_t)0x00100000U) /*!< Only partial address space was erased */ +#define SDMMC_ERROR_CARD_ECC_DISABLED ((uint32_t)0x00200000U) /*!< Command has been executed without using internal ECC */ +#define SDMMC_ERROR_ERASE_RESET ((uint32_t)0x00400000U) /*!< Erase sequence was cleared before executing because an out + of erase sequence command was received */ +#define SDMMC_ERROR_AKE_SEQ_ERR ((uint32_t)0x00800000U) /*!< Error in sequence of authentication */ +#define SDMMC_ERROR_INVALID_VOLTRANGE ((uint32_t)0x01000000U) /*!< Error in case of invalid voltage range */ +#define SDMMC_ERROR_ADDR_OUT_OF_RANGE ((uint32_t)0x02000000U) /*!< Error when addressed block is out of range */ +#define SDMMC_ERROR_REQUEST_NOT_APPLICABLE ((uint32_t)0x04000000U) /*!< Error when command request is not applicable */ +#define SDMMC_ERROR_INVALID_PARAMETER ((uint32_t)0x08000000U) /*!< the used parameter is not valid */ +#define SDMMC_ERROR_UNSUPPORTED_FEATURE ((uint32_t)0x10000000U) /*!< Error when feature is not insupported */ +#define SDMMC_ERROR_BUSY ((uint32_t)0x20000000U) /*!< Error when transfer process is busy */ +#define SDMMC_ERROR_DMA ((uint32_t)0x40000000U) /*!< Error while DMA transfer */ +#define SDMMC_ERROR_TIMEOUT ((uint32_t)0x80000000U) /*!< Timeout error */ + +/** + * @brief SDMMC Commands Index + */ +#define SDMMC_CMD_GO_IDLE_STATE ((uint8_t)0U) /*!< Resets the SD memory card. */ +#define SDMMC_CMD_SEND_OP_COND ((uint8_t)1U) /*!< Sends host capacity support information and activates the card's initialization process. */ +#define SDMMC_CMD_ALL_SEND_CID ((uint8_t)2U) /*!< Asks any card connected to the host to send the CID numbers on the CMD line. */ +#define SDMMC_CMD_SET_REL_ADDR ((uint8_t)3U) /*!< Asks the card to publish a new relative address (RCA). */ +#define SDMMC_CMD_SET_DSR ((uint8_t)4U) /*!< Programs the DSR of all cards. */ +#define SDMMC_CMD_SDMMC_SEN_OP_COND ((uint8_t)5U) /*!< Sends host capacity support information (HCS) and asks the accessed card to send its + operating condition register (OCR) content in the response on the CMD line. */ +#define SDMMC_CMD_HS_SWITCH ((uint8_t)6U) /*!< Checks switchable function (mode 0) and switch card function (mode 1). */ +#define SDMMC_CMD_SEL_DESEL_CARD ((uint8_t)7U) /*!< Selects the card by its own relative address and gets deselected by any other address */ +#define SDMMC_CMD_HS_SEND_EXT_CSD ((uint8_t)8U) /*!< Sends SD Memory Card interface condition, which includes host supply voltage information + and asks the card whether card supports voltage. */ +#define SDMMC_CMD_SEND_CSD ((uint8_t)9U) /*!< Addressed card sends its card specific data (CSD) on the CMD line. */ +#define SDMMC_CMD_SEND_CID ((uint8_t)10U) /*!< Addressed card sends its card identification (CID) on the CMD line. */ +#define SDMMC_CMD_READ_DAT_UNTIL_STOP ((uint8_t)11U) /*!< SD card doesn't support it. */ +#define SDMMC_CMD_STOP_TRANSMISSION ((uint8_t)12U) /*!< Forces the card to stop transmission. */ +#define SDMMC_CMD_SEND_STATUS ((uint8_t)13U) /*!< Addressed card sends its status register. */ +#define SDMMC_CMD_HS_BUSTEST_READ ((uint8_t)14U) /*!< Reserved */ +#define SDMMC_CMD_GO_INACTIVE_STATE ((uint8_t)15U) /*!< Sends an addressed card into the inactive state. */ +#define SDMMC_CMD_SET_BLOCKLEN ((uint8_t)16U) /*!< Sets the block length (in bytes for SDSC) for all following block commands + (read, write, lock). Default block length is fixed to 512 Bytes. Not effective + for SDHS and SDXC. */ +#define SDMMC_CMD_READ_SINGLE_BLOCK ((uint8_t)17U) /*!< Reads single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of + fixed 512 bytes in case of SDHC and SDXC. */ +#define SDMMC_CMD_READ_MULT_BLOCK ((uint8_t)18U) /*!< Continuously transfers data blocks from card to host until interrupted by + STOP_TRANSMISSION command. */ +#define SDMMC_CMD_HS_BUSTEST_WRITE ((uint8_t)19U) /*!< 64 bytes tuning pattern is sent for SDR50 and SDR104. */ +#define SDMMC_CMD_WRITE_DAT_UNTIL_STOP ((uint8_t)20U) /*!< Speed class control command. */ +#define SDMMC_CMD_SET_BLOCK_COUNT ((uint8_t)23U) /*!< Specify block count for CMD18 and CMD25. */ +#define SDMMC_CMD_WRITE_SINGLE_BLOCK ((uint8_t)24U) /*!< Writes single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of + fixed 512 bytes in case of SDHC and SDXC. */ +#define SDMMC_CMD_WRITE_MULT_BLOCK ((uint8_t)25U) /*!< Continuously writes blocks of data until a STOP_TRANSMISSION follows. */ +#define SDMMC_CMD_PROG_CID ((uint8_t)26U) /*!< Reserved for manufacturers. */ +#define SDMMC_CMD_PROG_CSD ((uint8_t)27U) /*!< Programming of the programmable bits of the CSD. */ +#define SDMMC_CMD_SET_WRITE_PROT ((uint8_t)28U) /*!< Sets the write protection bit of the addressed group. */ +#define SDMMC_CMD_CLR_WRITE_PROT ((uint8_t)29U) /*!< Clears the write protection bit of the addressed group. */ +#define SDMMC_CMD_SEND_WRITE_PROT ((uint8_t)30U) /*!< Asks the card to send the status of the write protection bits. */ +#define SDMMC_CMD_SD_ERASE_GRP_START ((uint8_t)32U) /*!< Sets the address of the first write block to be erased. (For SD card only). */ +#define SDMMC_CMD_SD_ERASE_GRP_END ((uint8_t)33U) /*!< Sets the address of the last write block of the continuous range to be erased. */ +#define SDMMC_CMD_ERASE_GRP_START ((uint8_t)35U) /*!< Sets the address of the first write block to be erased. Reserved for each command + system set by switch function command (CMD6). */ +#define SDMMC_CMD_ERASE_GRP_END ((uint8_t)36U) /*!< Sets the address of the last write block of the continuous range to be erased. + Reserved for each command system set by switch function command (CMD6). */ +#define SDMMC_CMD_ERASE ((uint8_t)38U) /*!< Reserved for SD security applications. */ +#define SDMMC_CMD_FAST_IO ((uint8_t)39U) /*!< SD card doesn't support it (Reserved). */ +#define SDMMC_CMD_GO_IRQ_STATE ((uint8_t)40U) /*!< SD card doesn't support it (Reserved). */ +#define SDMMC_CMD_LOCK_UNLOCK ((uint8_t)42U) /*!< Sets/resets the password or lock/unlock the card. The size of the data block is set by + the SET_BLOCK_LEN command. */ +#define SDMMC_CMD_APP_CMD ((uint8_t)55U) /*!< Indicates to the card that the next command is an application specific command rather + than a standard command. */ +#define SDMMC_CMD_GEN_CMD ((uint8_t)56U) /*!< Used either to transfer a data block to the card or to get a data block from the card + for general purpose/application specific commands. */ +#define SDMMC_CMD_NO_CMD ((uint8_t)64U) /*!< No command */ + +/** + * @brief Following commands are SD Card Specific commands. + * SDMMC_APP_CMD should be sent before sending these commands. + */ +#define SDMMC_CMD_APP_SD_SET_BUSWIDTH ((uint8_t)6U) /*!< (ACMD6) Defines the data bus width to be used for data transfer. The allowed data bus + widths are given in SCR register. */ +#define SDMMC_CMD_SD_APP_STATUS ((uint8_t)13U) /*!< (ACMD13) Sends the SD status. */ +#define SDMMC_CMD_SD_APP_SEND_NUM_WRITE_BLOCKS ((uint8_t)22U) /*!< (ACMD22) Sends the number of the written (without errors) write blocks. Responds with + 32bit+CRC data block. */ +#define SDMMC_CMD_SD_APP_OP_COND ((uint8_t)41U) /*!< (ACMD41) Sends host capacity support information (HCS) and asks the accessed card to + send its operating condition register (OCR) content in the response on the CMD line. */ +#define SDMMC_CMD_SD_APP_SET_CLR_CARD_DETECT ((uint8_t)42U) /*!< (ACMD42) Connect/Disconnect the 50 KOhm pull-up resistor on CD/DAT3 (pin 1) of the card */ +#define SDMMC_CMD_SD_APP_SEND_SCR ((uint8_t)51U) /*!< Reads the SD Configuration Register (SCR). */ +#define SDMMC_CMD_SDMMC_RW_DIRECT ((uint8_t)52U) /*!< For SD I/O card only, reserved for security specification. */ +#define SDMMC_CMD_SDMMC_RW_EXTENDED ((uint8_t)53U) /*!< For SD I/O card only, reserved for security specification. */ + +/** + * @brief Following commands are SD Card Specific security commands. + * SDMMC_CMD_APP_CMD should be sent before sending these commands. + */ +#define SDMMC_CMD_SD_APP_GET_MKB ((uint8_t)43U) +#define SDMMC_CMD_SD_APP_GET_MID ((uint8_t)44U) +#define SDMMC_CMD_SD_APP_SET_CER_RN1 ((uint8_t)45U) +#define SDMMC_CMD_SD_APP_GET_CER_RN2 ((uint8_t)46U) +#define SDMMC_CMD_SD_APP_SET_CER_RES2 ((uint8_t)47U) +#define SDMMC_CMD_SD_APP_GET_CER_RES1 ((uint8_t)48U) +#define SDMMC_CMD_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((uint8_t)18U) +#define SDMMC_CMD_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((uint8_t)25U) +#define SDMMC_CMD_SD_APP_SECURE_ERASE ((uint8_t)38U) +#define SDMMC_CMD_SD_APP_CHANGE_SECURE_AREA ((uint8_t)49U) +#define SDMMC_CMD_SD_APP_SECURE_WRITE_MKB ((uint8_t)48U) + +/** + * @brief Masks for errors Card Status R1 (OCR Register) + */ +#define SDMMC_OCR_ADDR_OUT_OF_RANGE ((uint32_t)0x80000000U) +#define SDMMC_OCR_ADDR_MISALIGNED ((uint32_t)0x40000000U) +#define SDMMC_OCR_BLOCK_LEN_ERR ((uint32_t)0x20000000U) +#define SDMMC_OCR_ERASE_SEQ_ERR ((uint32_t)0x10000000U) +#define SDMMC_OCR_BAD_ERASE_PARAM ((uint32_t)0x08000000U) +#define SDMMC_OCR_WRITE_PROT_VIOLATION ((uint32_t)0x04000000U) +#define SDMMC_OCR_LOCK_UNLOCK_FAILED ((uint32_t)0x01000000U) +#define SDMMC_OCR_COM_CRC_FAILED ((uint32_t)0x00800000U) +#define SDMMC_OCR_ILLEGAL_CMD ((uint32_t)0x00400000U) +#define SDMMC_OCR_CARD_ECC_FAILED ((uint32_t)0x00200000U) +#define SDMMC_OCR_CC_ERROR ((uint32_t)0x00100000U) +#define SDMMC_OCR_GENERAL_UNKNOWN_ERROR ((uint32_t)0x00080000U) +#define SDMMC_OCR_STREAM_READ_UNDERRUN ((uint32_t)0x00040000U) +#define SDMMC_OCR_STREAM_WRITE_OVERRUN ((uint32_t)0x00020000U) +#define SDMMC_OCR_CID_CSD_OVERWRITE ((uint32_t)0x00010000U) +#define SDMMC_OCR_WP_ERASE_SKIP ((uint32_t)0x00008000U) +#define SDMMC_OCR_CARD_ECC_DISABLED ((uint32_t)0x00004000U) +#define SDMMC_OCR_ERASE_RESET ((uint32_t)0x00002000U) +#define SDMMC_OCR_AKE_SEQ_ERROR ((uint32_t)0x00000008U) +#define SDMMC_OCR_ERRORBITS ((uint32_t)0xFDFFE008U) + +/** + * @brief Masks for R6 Response + */ +#define SDMMC_R6_GENERAL_UNKNOWN_ERROR ((uint32_t)0x00002000U) +#define SDMMC_R6_ILLEGAL_CMD ((uint32_t)0x00004000U) +#define SDMMC_R6_COM_CRC_FAILED ((uint32_t)0x00008000U) + +#define SDMMC_VOLTAGE_WINDOW_SD ((uint32_t)0x80100000U) +#define SDMMC_HIGH_CAPACITY ((uint32_t)0x40000000U) +#define SDMMC_STD_CAPACITY ((uint32_t)0x00000000U) +#define SDMMC_CHECK_PATTERN ((uint32_t)0x000001AAU) +#define SD_SWITCH_1_8V_CAPACITY ((uint32_t)0x01000000U) + +#define SDMMC_MAX_VOLT_TRIAL ((uint32_t)0x0000FFFFU) + +#define SDMMC_MAX_TRIAL ((uint32_t)0x0000FFFFU) + +#define SDMMC_ALLZERO ((uint32_t)0x00000000U) + +#define SDMMC_WIDE_BUS_SUPPORT ((uint32_t)0x00040000U) +#define SDMMC_SINGLE_BUS_SUPPORT ((uint32_t)0x00010000U) +#define SDMMC_CARD_LOCKED ((uint32_t)0x02000000U) + +#define SDMMC_DATATIMEOUT ((uint32_t)5000U) + +#define SDMMC_0TO7BITS ((uint32_t)0x000000FFU) +#define SDMMC_8TO15BITS ((uint32_t)0x0000FF00U) +#define SDMMC_16TO23BITS ((uint32_t)0x00FF0000U) +#define SDMMC_24TO31BITS ((uint32_t)0xFF000000U) +#define SDMMC_MAX_DATA_LENGTH ((uint32_t)0x01FFFFFFU) + +#define SDMMC_HALFFIFO ((uint32_t)0x00000008U) +#define SDMMC_HALFFIFOBYTES ((uint32_t)0x00000020U) + +/** + * @brief Command Class supported + */ +#define SDIO_CCCC_ERASE ((uint32_t)0x00000020U) + +#define SDIO_CMDTIMEOUT ((uint32_t)5000U) /* Command send and response timeout */ +#define SDIO_MAXERASETIMEOUT ((uint32_t)63000U) /* Max erase Timeout 63 s */ +#define SDIO_STOPTRANSFERTIMEOUT ((uint32_t)100000000U) /* Timeout for STOP TRANSMISSION command */ + +/** @defgroup SDIO_LL_Clock_Edge Clock Edge + * @{ + */ +#define SDIO_CLOCK_EDGE_RISING ((uint32_t)0x00000000U) +#define SDIO_CLOCK_EDGE_FALLING SDIO_CLKCR_NEGEDGE + +#define IS_SDIO_CLOCK_EDGE(EDGE) (((EDGE) == SDIO_CLOCK_EDGE_RISING) || \ + ((EDGE) == SDIO_CLOCK_EDGE_FALLING)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Clock_Bypass Clock Bypass + * @{ + */ +#define SDIO_CLOCK_BYPASS_DISABLE ((uint32_t)0x00000000U) +#define SDIO_CLOCK_BYPASS_ENABLE SDIO_CLKCR_BYPASS + +#define IS_SDIO_CLOCK_BYPASS(BYPASS) (((BYPASS) == SDIO_CLOCK_BYPASS_DISABLE) || \ + ((BYPASS) == SDIO_CLOCK_BYPASS_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Clock_Power_Save Clock Power Saving + * @{ + */ +#define SDIO_CLOCK_POWER_SAVE_DISABLE ((uint32_t)0x00000000U) +#define SDIO_CLOCK_POWER_SAVE_ENABLE SDIO_CLKCR_PWRSAV + +#define IS_SDIO_CLOCK_POWER_SAVE(SAVE) (((SAVE) == SDIO_CLOCK_POWER_SAVE_DISABLE) || \ + ((SAVE) == SDIO_CLOCK_POWER_SAVE_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Bus_Wide Bus Width + * @{ + */ +#define SDIO_BUS_WIDE_1B ((uint32_t)0x00000000U) +#define SDIO_BUS_WIDE_4B SDIO_CLKCR_WIDBUS_0 +#define SDIO_BUS_WIDE_8B SDIO_CLKCR_WIDBUS_1 + +#define IS_SDIO_BUS_WIDE(WIDE) (((WIDE) == SDIO_BUS_WIDE_1B) || \ + ((WIDE) == SDIO_BUS_WIDE_4B) || \ + ((WIDE) == SDIO_BUS_WIDE_8B)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Hardware_Flow_Control Hardware Flow Control + * @{ + */ +#define SDIO_HARDWARE_FLOW_CONTROL_DISABLE ((uint32_t)0x00000000U) +#define SDIO_HARDWARE_FLOW_CONTROL_ENABLE SDIO_CLKCR_HWFC_EN + +#define IS_SDIO_HARDWARE_FLOW_CONTROL(CONTROL) (((CONTROL) == SDIO_HARDWARE_FLOW_CONTROL_DISABLE) || \ + ((CONTROL) == SDIO_HARDWARE_FLOW_CONTROL_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Clock_Division Clock Division + * @{ + */ +#define IS_SDIO_CLKDIV(DIV) ((DIV) <= 0xFFU) +/** + * @} + */ + +/** @defgroup SDIO_LL_Command_Index Command Index + * @{ + */ +#define IS_SDIO_CMD_INDEX(INDEX) ((INDEX) < 0x40U) +/** + * @} + */ + +/** @defgroup SDIO_LL_Response_Type Response Type + * @{ + */ +#define SDIO_RESPONSE_NO ((uint32_t)0x00000000U) +#define SDIO_RESPONSE_SHORT SDIO_CMD_WAITRESP_0 +#define SDIO_RESPONSE_LONG SDIO_CMD_WAITRESP + +#define IS_SDIO_RESPONSE(RESPONSE) (((RESPONSE) == SDIO_RESPONSE_NO) || \ + ((RESPONSE) == SDIO_RESPONSE_SHORT) || \ + ((RESPONSE) == SDIO_RESPONSE_LONG)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Wait_Interrupt_State Wait Interrupt + * @{ + */ +#define SDIO_WAIT_NO ((uint32_t)0x00000000U) +#define SDIO_WAIT_IT SDIO_CMD_WAITINT +#define SDIO_WAIT_PEND SDIO_CMD_WAITPEND + +#define IS_SDIO_WAIT(WAIT) (((WAIT) == SDIO_WAIT_NO) || \ + ((WAIT) == SDIO_WAIT_IT) || \ + ((WAIT) == SDIO_WAIT_PEND)) +/** + * @} + */ + +/** @defgroup SDIO_LL_CPSM_State CPSM State + * @{ + */ +#define SDIO_CPSM_DISABLE ((uint32_t)0x00000000U) +#define SDIO_CPSM_ENABLE SDIO_CMD_CPSMEN + +#define IS_SDIO_CPSM(CPSM) (((CPSM) == SDIO_CPSM_DISABLE) || \ + ((CPSM) == SDIO_CPSM_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Response_Registers Response Register + * @{ + */ +#define SDIO_RESP1 ((uint32_t)0x00000000U) +#define SDIO_RESP2 ((uint32_t)0x00000004U) +#define SDIO_RESP3 ((uint32_t)0x00000008U) +#define SDIO_RESP4 ((uint32_t)0x0000000CU) + +#define IS_SDIO_RESP(RESP) (((RESP) == SDIO_RESP1) || \ + ((RESP) == SDIO_RESP2) || \ + ((RESP) == SDIO_RESP3) || \ + ((RESP) == SDIO_RESP4)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Data_Length Data Lenght + * @{ + */ +#define IS_SDIO_DATA_LENGTH(LENGTH) ((LENGTH) <= 0x01FFFFFFU) +/** + * @} + */ + +/** @defgroup SDIO_LL_Data_Block_Size Data Block Size + * @{ + */ +#define SDIO_DATABLOCK_SIZE_1B ((uint32_t)0x00000000U) +#define SDIO_DATABLOCK_SIZE_2B SDIO_DCTRL_DBLOCKSIZE_0 +#define SDIO_DATABLOCK_SIZE_4B SDIO_DCTRL_DBLOCKSIZE_1 +#define SDIO_DATABLOCK_SIZE_8B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1) +#define SDIO_DATABLOCK_SIZE_16B SDIO_DCTRL_DBLOCKSIZE_2 +#define SDIO_DATABLOCK_SIZE_32B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_2) +#define SDIO_DATABLOCK_SIZE_64B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2) +#define SDIO_DATABLOCK_SIZE_128B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2) +#define SDIO_DATABLOCK_SIZE_256B SDIO_DCTRL_DBLOCKSIZE_3 +#define SDIO_DATABLOCK_SIZE_512B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_1024B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_2048B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_4096B (SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_8192B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_16384B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) + +#define IS_SDIO_BLOCK_SIZE(SIZE) (((SIZE) == SDIO_DATABLOCK_SIZE_1B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_2B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_4B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_8B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_16B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_32B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_64B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_128B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_256B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_512B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_1024B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_2048B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_4096B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_8192B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_16384B)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Transfer_Direction Transfer Direction + * @{ + */ +#define SDIO_TRANSFER_DIR_TO_CARD ((uint32_t)0x00000000U) +#define SDIO_TRANSFER_DIR_TO_SDIO SDIO_DCTRL_DTDIR + +#define IS_SDIO_TRANSFER_DIR(DIR) (((DIR) == SDIO_TRANSFER_DIR_TO_CARD) || \ + ((DIR) == SDIO_TRANSFER_DIR_TO_SDIO)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Transfer_Type Transfer Type + * @{ + */ +#define SDIO_TRANSFER_MODE_BLOCK ((uint32_t)0x00000000U) +#define SDIO_TRANSFER_MODE_STREAM SDIO_DCTRL_DTMODE + +#define IS_SDIO_TRANSFER_MODE(MODE) (((MODE) == SDIO_TRANSFER_MODE_BLOCK) || \ + ((MODE) == SDIO_TRANSFER_MODE_STREAM)) +/** + * @} + */ + +/** @defgroup SDIO_LL_DPSM_State DPSM State + * @{ + */ +#define SDIO_DPSM_DISABLE ((uint32_t)0x00000000U) +#define SDIO_DPSM_ENABLE SDIO_DCTRL_DTEN + +#define IS_SDIO_DPSM(DPSM) (((DPSM) == SDIO_DPSM_DISABLE) ||\ + ((DPSM) == SDIO_DPSM_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Read_Wait_Mode Read Wait Mode + * @{ + */ +#define SDIO_READ_WAIT_MODE_DATA2 ((uint32_t)0x00000000U) +#define SDIO_READ_WAIT_MODE_CLK (SDIO_DCTRL_RWMOD) + +#define IS_SDIO_READWAIT_MODE(MODE) (((MODE) == SDIO_READ_WAIT_MODE_CLK) || \ + ((MODE) == SDIO_READ_WAIT_MODE_DATA2)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Interrupt_sources Interrupt Sources + * @{ + */ +#define SDIO_IT_CCRCFAIL SDIO_MASK_CCRCFAILIE +#define SDIO_IT_DCRCFAIL SDIO_MASK_DCRCFAILIE +#define SDIO_IT_CTIMEOUT SDIO_MASK_CTIMEOUTIE +#define SDIO_IT_DTIMEOUT SDIO_MASK_DTIMEOUTIE +#define SDIO_IT_TXUNDERR SDIO_MASK_TXUNDERRIE +#define SDIO_IT_RXOVERR SDIO_MASK_RXOVERRIE +#define SDIO_IT_CMDREND SDIO_MASK_CMDRENDIE +#define SDIO_IT_CMDSENT SDIO_MASK_CMDSENTIE +#define SDIO_IT_DATAEND SDIO_MASK_DATAENDIE +#define SDIO_IT_STBITERR SDIO_MASK_STBITERRIE +#define SDIO_IT_DBCKEND SDIO_MASK_DBCKENDIE +#define SDIO_IT_CMDACT SDIO_MASK_CMDACTIE +#define SDIO_IT_TXACT SDIO_MASK_TXACTIE +#define SDIO_IT_RXACT SDIO_MASK_RXACTIE +#define SDIO_IT_TXFIFOHE SDIO_MASK_TXFIFOHEIE +#define SDIO_IT_RXFIFOHF SDIO_MASK_RXFIFOHFIE +#define SDIO_IT_TXFIFOF SDIO_MASK_TXFIFOFIE +#define SDIO_IT_RXFIFOF SDIO_MASK_RXFIFOFIE +#define SDIO_IT_TXFIFOE SDIO_MASK_TXFIFOEIE +#define SDIO_IT_RXFIFOE SDIO_MASK_RXFIFOEIE +#define SDIO_IT_TXDAVL SDIO_MASK_TXDAVLIE +#define SDIO_IT_RXDAVL SDIO_MASK_RXDAVLIE +#define SDIO_IT_SDIOIT SDIO_MASK_SDIOITIE +#define SDIO_IT_CEATAEND SDIO_MASK_CEATAENDIE +/** + * @} + */ + +/** @defgroup SDIO_LL_Flags Flags + * @{ + */ +#define SDIO_FLAG_CCRCFAIL SDIO_STA_CCRCFAIL +#define SDIO_FLAG_DCRCFAIL SDIO_STA_DCRCFAIL +#define SDIO_FLAG_CTIMEOUT SDIO_STA_CTIMEOUT +#define SDIO_FLAG_DTIMEOUT SDIO_STA_DTIMEOUT +#define SDIO_FLAG_TXUNDERR SDIO_STA_TXUNDERR +#define SDIO_FLAG_RXOVERR SDIO_STA_RXOVERR +#define SDIO_FLAG_CMDREND SDIO_STA_CMDREND +#define SDIO_FLAG_CMDSENT SDIO_STA_CMDSENT +#define SDIO_FLAG_DATAEND SDIO_STA_DATAEND +#define SDIO_FLAG_STBITERR SDIO_STA_STBITERR +#define SDIO_FLAG_DBCKEND SDIO_STA_DBCKEND +#define SDIO_FLAG_CMDACT SDIO_STA_CMDACT +#define SDIO_FLAG_TXACT SDIO_STA_TXACT +#define SDIO_FLAG_RXACT SDIO_STA_RXACT +#define SDIO_FLAG_TXFIFOHE SDIO_STA_TXFIFOHE +#define SDIO_FLAG_RXFIFOHF SDIO_STA_RXFIFOHF +#define SDIO_FLAG_TXFIFOF SDIO_STA_TXFIFOF +#define SDIO_FLAG_RXFIFOF SDIO_STA_RXFIFOF +#define SDIO_FLAG_TXFIFOE SDIO_STA_TXFIFOE +#define SDIO_FLAG_RXFIFOE SDIO_STA_RXFIFOE +#define SDIO_FLAG_TXDAVL SDIO_STA_TXDAVL +#define SDIO_FLAG_RXDAVL SDIO_STA_RXDAVL +#define SDIO_FLAG_SDIOIT SDIO_STA_SDIOIT +#define SDIO_FLAG_CEATAEND SDIO_STA_CEATAEND +#define SDIO_STATIC_FLAGS ((uint32_t)(SDIO_FLAG_CCRCFAIL | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_CTIMEOUT |\ + SDIO_FLAG_DTIMEOUT | SDIO_FLAG_TXUNDERR | SDIO_FLAG_RXOVERR |\ + SDIO_FLAG_CMDREND | SDIO_FLAG_CMDSENT | SDIO_FLAG_DATAEND |\ + SDIO_FLAG_DBCKEND | SDIO_FLAG_SDIOIT)) + +#define SDIO_STATIC_CMD_FLAGS ((uint32_t)(SDIO_FLAG_CCRCFAIL | SDIO_FLAG_CTIMEOUT | SDIO_FLAG_CMDREND |\ + SDIO_FLAG_CMDSENT)) + +#define SDIO_STATIC_DATA_FLAGS ((uint32_t)(SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_TXUNDERR |\ + SDIO_FLAG_RXOVERR | SDIO_FLAG_DATAEND | SDIO_FLAG_DBCKEND)) +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup SDIO_LL_Exported_macros SDIO_LL Exported Macros * @{ */ -#ifdef HAL_TIM_MODULE_ENABLED +/** @defgroup SDMMC_LL_Alias_Region Bit Address in the alias region + * @{ + */ +/* ------------ SDIO registers bit address in the alias region -------------- */ +#define SDIO_OFFSET (SDIO_BASE - PERIPH_BASE) -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private function prototypes -----------------------------------------------*/ -static void TIM_CCxNChannelCmd(TIM_TypeDef *TIMx, uint32_t Channel, uint32_t ChannelNState); +/* --- CLKCR Register ---*/ +/* Alias word address of CLKEN bit */ +#define CLKCR_OFFSET (SDIO_OFFSET + 0x04U) +#define CLKEN_BITNUMBER 0x08U +#define CLKCR_CLKEN_BB (PERIPH_BB_BASE + (CLKCR_OFFSET * 32U) + (CLKEN_BITNUMBER * 4U)) + +/* --- CMD Register ---*/ +/* Alias word address of SDIOSUSPEND bit */ +#define CMD_OFFSET (SDIO_OFFSET + 0x0CU) +#define SDIOSUSPEND_BITNUMBER 0x0BU +#define CMD_SDIOSUSPEND_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (SDIOSUSPEND_BITNUMBER * 4U)) + +/* Alias word address of ENCMDCOMPL bit */ +#define ENCMDCOMPL_BITNUMBER 0x0CU +#define CMD_ENCMDCOMPL_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (ENCMDCOMPL_BITNUMBER * 4U)) + +/* Alias word address of NIEN bit */ +#define NIEN_BITNUMBER 0x0DU +#define CMD_NIEN_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (NIEN_BITNUMBER * 4U)) + +/* Alias word address of ATACMD bit */ +#define ATACMD_BITNUMBER 0x0EU +#define CMD_ATACMD_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (ATACMD_BITNUMBER * 4U)) + +/* --- DCTRL Register ---*/ +/* Alias word address of DMAEN bit */ +#define DCTRL_OFFSET (SDIO_OFFSET + 0x2CU) +#define DMAEN_BITNUMBER 0x03U +#define DCTRL_DMAEN_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (DMAEN_BITNUMBER * 4U)) + +/* Alias word address of RWSTART bit */ +#define RWSTART_BITNUMBER 0x08U +#define DCTRL_RWSTART_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWSTART_BITNUMBER * 4U)) + +/* Alias word address of RWSTOP bit */ +#define RWSTOP_BITNUMBER 0x09U +#define DCTRL_RWSTOP_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWSTOP_BITNUMBER * 4U)) + +/* Alias word address of RWMOD bit */ +#define RWMOD_BITNUMBER 0x0AU +#define DCTRL_RWMOD_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWMOD_BITNUMBER * 4U)) + +/* Alias word address of SDIOEN bit */ +#define SDIOEN_BITNUMBER 0x0BU +#define DCTRL_SDIOEN_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (SDIOEN_BITNUMBER * 4U)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Register Bits And Addresses Definitions + * @brief SDIO_LL registers bit address in the alias region + * @{ + */ +/* ---------------------- SDIO registers bit mask --------------------------- */ +/* --- CLKCR Register ---*/ +/* CLKCR register clear mask */ +#define CLKCR_CLEAR_MASK ((uint32_t)(SDIO_CLKCR_CLKDIV | SDIO_CLKCR_PWRSAV |\ + SDIO_CLKCR_BYPASS | SDIO_CLKCR_WIDBUS |\ + SDIO_CLKCR_NEGEDGE | SDIO_CLKCR_HWFC_EN)) + +/* --- DCTRL Register ---*/ +/* SDIO DCTRL Clear Mask */ +#define DCTRL_CLEAR_MASK ((uint32_t)(SDIO_DCTRL_DTEN | SDIO_DCTRL_DTDIR |\ + SDIO_DCTRL_DTMODE | SDIO_DCTRL_DBLOCKSIZE)) + +/* --- CMD Register ---*/ +/* CMD Register clear mask */ +#define CMD_CLEAR_MASK ((uint32_t)(SDIO_CMD_CMDINDEX | SDIO_CMD_WAITRESP |\ + SDIO_CMD_WAITINT | SDIO_CMD_WAITPEND |\ + SDIO_CMD_CPSMEN | SDIO_CMD_SDIOSUSPEND)) + +/* SDIO Initialization Frequency (400KHz max) */ +#define SDIO_INIT_CLK_DIV ((uint8_t)0x76) /* 48MHz / (SDMMC_INIT_CLK_DIV + 2) < 400KHz */ + +/* SDIO Data Transfer Frequency (25MHz max) */ +#define SDIO_TRANSFER_CLK_DIV ((uint8_t)0x2) +/** + * @} + */ + +/** @defgroup SDIO_LL_Interrupt_Clock Interrupt And Clock Configuration + * @brief macros to handle interrupts and specific clock configurations + * @{ + */ + +/** + * @brief Enable the SDIO device. + * @param __INSTANCE__: SDIO Instance + * @retval None + */ +#define __SDIO_ENABLE(__INSTANCE__) (*(__IO uint32_t *)CLKCR_CLKEN_BB = ENABLE) + +/** + * @brief Disable the SDIO device. + * @param __INSTANCE__: SDIO Instance + * @retval None + */ +#define __SDIO_DISABLE(__INSTANCE__) (*(__IO uint32_t *)CLKCR_CLKEN_BB = DISABLE) + +/** + * @brief Enable the SDIO DMA transfer. + * @param __INSTANCE__: SDIO Instance + * @retval None + */ +#define __SDIO_DMA_ENABLE(__INSTANCE__) (*(__IO uint32_t *)DCTRL_DMAEN_BB = ENABLE) + +/** + * @brief Disable the SDIO DMA transfer. + * @param __INSTANCE__: SDIO Instance + * @retval None + */ +#define __SDIO_DMA_DISABLE(__INSTANCE__) (*(__IO uint32_t *)DCTRL_DMAEN_BB = DISABLE) + +/** + * @brief Enable the SDIO device interrupt. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __INTERRUPT__ : specifies the SDIO interrupt sources to be enabled. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SDIO interrupt received interrupt + * @retval None + */ +#define __SDIO_ENABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK |= (__INTERRUPT__)) + +/** + * @brief Disable the SDIO device interrupt. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __INTERRUPT__ : specifies the SDIO interrupt sources to be disabled. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SDIO interrupt received interrupt + * @retval None + */ +#define __SDIO_DISABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK &= ~(__INTERRUPT__)) + +/** + * @brief Checks whether the specified SDIO flag is set or not. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) + * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) + * @arg SDIO_FLAG_CTIMEOUT: Command response timeout + * @arg SDIO_FLAG_DTIMEOUT: Data timeout + * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error + * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error + * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) + * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) + * @arg SDIO_FLAG_DATAEND: Data end (data counter, DATACOUNT, is zero) + * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) + * @arg SDIO_FLAG_CMDACT: Command transfer in progress + * @arg SDIO_FLAG_TXACT: Data transmit in progress + * @arg SDIO_FLAG_RXACT: Data receive in progress + * @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty + * @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full + * @arg SDIO_FLAG_TXFIFOF: Transmit FIFO full + * @arg SDIO_FLAG_RXFIFOF: Receive FIFO full + * @arg SDIO_FLAG_TXFIFOE: Transmit FIFO empty + * @arg SDIO_FLAG_RXFIFOE: Receive FIFO empty + * @arg SDIO_FLAG_TXDAVL: Data available in transmit FIFO + * @arg SDIO_FLAG_RXDAVL: Data available in receive FIFO + * @arg SDIO_FLAG_SDIOIT: SDIO interrupt received + * @retval The new state of SDIO_FLAG (SET or RESET). + */ +#define __SDIO_GET_FLAG(__INSTANCE__, __FLAG__) (((__INSTANCE__)->STA &(__FLAG__)) != 0U) + + +/** + * @brief Clears the SDIO pending flags. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __FLAG__: specifies the flag to clear. + * This parameter can be one or a combination of the following values: + * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) + * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) + * @arg SDIO_FLAG_CTIMEOUT: Command response timeout + * @arg SDIO_FLAG_DTIMEOUT: Data timeout + * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error + * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error + * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) + * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) + * @arg SDIO_FLAG_DATAEND: Data end (data counter, DATACOUNT, is zero) + * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) + * @arg SDIO_FLAG_SDIOIT: SDIO interrupt received + * @retval None + */ +#define __SDIO_CLEAR_FLAG(__INSTANCE__, __FLAG__) ((__INSTANCE__)->ICR = (__FLAG__)) + +/** + * @brief Checks whether the specified SDIO interrupt has occurred or not. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __INTERRUPT__: specifies the SDIO interrupt source to check. + * This parameter can be one of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SDIO interrupt received interrupt + * @retval The new state of SDIO_IT (SET or RESET). + */ +#define __SDIO_GET_IT (__INSTANCE__, __INTERRUPT__) (((__INSTANCE__)->STA &(__INTERRUPT__)) == (__INTERRUPT__)) + +/** + * @brief Clears the SDIO's interrupt pending bits. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __INTERRUPT__: specifies the interrupt pending bit to clear. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt + * @arg SDIO_IT_SDIOIT: SDIO interrupt received interrupt + * @retval None + */ +#define __SDIO_CLEAR_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->ICR = (__INTERRUPT__)) + +/** + * @brief Enable Start the SD I/O Read Wait operation. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_START_READWAIT_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTART_BB = ENABLE) + +/** + * @brief Disable Start the SD I/O Read Wait operations. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_START_READWAIT_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTART_BB = DISABLE) + +/** + * @brief Enable Start the SD I/O Read Wait operation. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_STOP_READWAIT_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTOP_BB = ENABLE) + +/** + * @brief Disable Stop the SD I/O Read Wait operations. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_STOP_READWAIT_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTOP_BB = DISABLE) + +/** + * @brief Enable the SD I/O Mode Operation. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_OPERATION_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_SDIOEN_BB = ENABLE) + +/** + * @brief Disable the SD I/O Mode Operation. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_OPERATION_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_SDIOEN_BB = DISABLE) + +/** + * @brief Enable the SD I/O Suspend command sending. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_SUSPEND_CMD_ENABLE(__INSTANCE__) (*(__IO uint32_t *) CMD_SDIOSUSPEND_BB = ENABLE) + +/** + * @brief Disable the SD I/O Suspend command sending. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_SUSPEND_CMD_DISABLE(__INSTANCE__) (*(__IO uint32_t *) CMD_SDIOSUSPEND_BB = DISABLE) + +/** + * @brief Enable the command completion signal. + * @retval None + */ +#define __SDIO_CEATA_CMD_COMPLETION_ENABLE() (*(__IO uint32_t *) CMD_ENCMDCOMPL_BB = ENABLE) + +/** + * @brief Disable the command completion signal. + * @retval None + */ +#define __SDIO_CEATA_CMD_COMPLETION_DISABLE() (*(__IO uint32_t *) CMD_ENCMDCOMPL_BB = DISABLE) + +/** + * @brief Enable the CE-ATA interrupt. + * @retval None + */ +#define __SDIO_CEATA_ENABLE_IT() (*(__IO uint32_t *) CMD_NIEN_BB = (uint32_t)0U) + +/** + * @brief Disable the CE-ATA interrupt. + * @retval None + */ +#define __SDIO_CEATA_DISABLE_IT() (*(__IO uint32_t *) CMD_NIEN_BB = (uint32_t)1U) + +/** + * @brief Enable send CE-ATA command (CMD61). + * @retval None + */ +#define __SDIO_CEATA_SENDCMD_ENABLE() (*(__IO uint32_t *) CMD_ATACMD_BB = ENABLE) + +/** + * @brief Disable send CE-ATA command (CMD61). + * @retval None + */ +#define __SDIO_CEATA_SENDCMD_DISABLE() (*(__IO uint32_t *) CMD_ATACMD_BB = DISABLE) + +/** + * @} + */ + +/** + * @} + */ /* Exported functions --------------------------------------------------------*/ -/** @defgroup TIMEx_Exported_Functions TIM Extended Exported Functions +/** @addtogroup SDMMC_LL_Exported_Functions * @{ */ - -/** @defgroup TIMEx_Exported_Functions_Group1 Extended Timer Hall Sensor functions - * @brief Timer Hall Sensor functions - * -@verbatim - ============================================================================== - ##### Timer Hall Sensor functions ##### - ============================================================================== - [..] - This section provides functions allowing to: - (+) Initialize and configure TIM HAL Sensor. - (+) De-initialize TIM HAL Sensor. - (+) Start the Hall Sensor Interface. - (+) Stop the Hall Sensor Interface. - (+) Start the Hall Sensor Interface and enable interrupts. - (+) Stop the Hall Sensor Interface and disable interrupts. - (+) Start the Hall Sensor Interface and enable DMA transfers. - (+) Stop the Hall Sensor Interface and disable DMA transfers. - -@endverbatim + +/* Initialization/de-initialization functions **********************************/ +/** @addtogroup HAL_SDMMC_LL_Group1 * @{ */ -/** - * @brief Initializes the TIM Hall Sensor Interface and initialize the associated handle. - * @param htim TIM Hall Sensor Interface handle - * @param sConfig TIM Hall Sensor configuration structure - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSensor_InitTypeDef *sConfig) -{ - TIM_OC_InitTypeDef OC_Config; - - /* Check the TIM handle allocation */ - if (htim == NULL) - { - return HAL_ERROR; - } - - /* Check the parameters */ - assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); - assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); - assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); - assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity)); - assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler)); - assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter)); - - if (htim->State == HAL_TIM_STATE_RESET) - { - /* Allocate lock resource and initialize it */ - htim->Lock = HAL_UNLOCKED; - -#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) - /* Reset interrupt callbacks to legacy week callbacks */ - TIM_ResetCallback(htim); - - if (htim->HallSensor_MspInitCallback == NULL) - { - htim->HallSensor_MspInitCallback = HAL_TIMEx_HallSensor_MspInit; - } - /* Init the low level hardware : GPIO, CLOCK, NVIC */ - htim->HallSensor_MspInitCallback(htim); -#else - /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ - HAL_TIMEx_HallSensor_MspInit(htim); -#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ - } - - /* Set the TIM state */ - htim->State = HAL_TIM_STATE_BUSY; - - /* Configure the Time base in the Encoder Mode */ - TIM_Base_SetConfig(htim->Instance, &htim->Init); - - /* Configure the Channel 1 as Input Channel to interface with the three Outputs of the Hall sensor */ - TIM_TI1_SetConfig(htim->Instance, sConfig->IC1Polarity, TIM_ICSELECTION_TRC, sConfig->IC1Filter); - - /* Reset the IC1PSC Bits */ - htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC; - /* Set the IC1PSC value */ - htim->Instance->CCMR1 |= sConfig->IC1Prescaler; - - /* Enable the Hall sensor interface (XOR function of the three inputs) */ - htim->Instance->CR2 |= TIM_CR2_TI1S; - - /* Select the TIM_TS_TI1F_ED signal as Input trigger for the TIM */ - htim->Instance->SMCR &= ~TIM_SMCR_TS; - htim->Instance->SMCR |= TIM_TS_TI1F_ED; - - /* Use the TIM_TS_TI1F_ED signal to reset the TIM counter each edge detection */ - htim->Instance->SMCR &= ~TIM_SMCR_SMS; - htim->Instance->SMCR |= TIM_SLAVEMODE_RESET; - - /* Program channel 2 in PWM 2 mode with the desired Commutation_Delay*/ - OC_Config.OCFastMode = TIM_OCFAST_DISABLE; - OC_Config.OCIdleState = TIM_OCIDLESTATE_RESET; - OC_Config.OCMode = TIM_OCMODE_PWM2; - OC_Config.OCNIdleState = TIM_OCNIDLESTATE_RESET; - OC_Config.OCNPolarity = TIM_OCNPOLARITY_HIGH; - OC_Config.OCPolarity = TIM_OCPOLARITY_HIGH; - OC_Config.Pulse = sConfig->Commutation_Delay; - - TIM_OC2_SetConfig(htim->Instance, &OC_Config); - - /* Select OC2REF as trigger output on TRGO: write the MMS bits in the TIMx_CR2 - register to 101 */ - htim->Instance->CR2 &= ~TIM_CR2_MMS; - htim->Instance->CR2 |= TIM_TRGO_OC2REF; - - /* Initialize the TIM state*/ - htim->State = HAL_TIM_STATE_READY; - - return HAL_OK; -} - -/** - * @brief DeInitializes the TIM Hall Sensor interface - * @param htim TIM Hall Sensor Interface handle - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef *htim) -{ - /* Check the parameters */ - assert_param(IS_TIM_INSTANCE(htim->Instance)); - - htim->State = HAL_TIM_STATE_BUSY; - - /* Disable the TIM Peripheral Clock */ - __HAL_TIM_DISABLE(htim); - -#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) - if (htim->HallSensor_MspDeInitCallback == NULL) - { - htim->HallSensor_MspDeInitCallback = HAL_TIMEx_HallSensor_MspDeInit; - } - /* DeInit the low level hardware */ - htim->HallSensor_MspDeInitCallback(htim); -#else - /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ - HAL_TIMEx_HallSensor_MspDeInit(htim); -#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ - - /* Change TIM state */ - htim->State = HAL_TIM_STATE_RESET; - - /* Release Lock */ - __HAL_UNLOCK(htim); - - return HAL_OK; -} - -/** - * @brief Initializes the TIM Hall Sensor MSP. - * @param htim TIM Hall Sensor Interface handle - * @retval None - */ -__weak void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef *htim) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(htim); - - /* NOTE : This function should not be modified, when the callback is needed, - the HAL_TIMEx_HallSensor_MspInit could be implemented in the user file - */ -} - -/** - * @brief DeInitializes TIM Hall Sensor MSP. - * @param htim TIM Hall Sensor Interface handle - * @retval None - */ -__weak void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef *htim) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(htim); - - /* NOTE : This function should not be modified, when the callback is needed, - the HAL_TIMEx_HallSensor_MspDeInit could be implemented in the user file - */ -} - -/** - * @brief Starts the TIM Hall Sensor Interface. - * @param htim TIM Hall Sensor Interface handle - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef *htim) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - - /* Enable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ - TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the TIM Hall sensor Interface. - * @param htim TIM Hall Sensor Interface handle - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim) -{ - /* Check the parameters */ - assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - - /* Disable the Input Capture channels 1, 2 and 3 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ - TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Starts the TIM Hall Sensor Interface in interrupt mode. - * @param htim TIM Hall Sensor Interface handle - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef *htim) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - - /* Enable the capture compare Interrupts 1 event */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); - - /* Enable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ - TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the TIM Hall Sensor Interface in interrupt mode. - * @param htim TIM Hall Sensor Interface handle - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim) -{ - /* Check the parameters */ - assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - - /* Disable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ - TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); - - /* Disable the capture compare Interrupts event */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Starts the TIM Hall Sensor Interface in DMA mode. - * @param htim TIM Hall Sensor Interface handle - * @param pData The destination Buffer address. - * @param Length The length of data to be transferred from TIM peripheral to memory. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - - if (htim->State == HAL_TIM_STATE_BUSY) - { - return HAL_BUSY; - } - else if (htim->State == HAL_TIM_STATE_READY) - { - if (((uint32_t)pData == 0U) && (Length > 0U)) - { - return HAL_ERROR; - } - else - { - htim->State = HAL_TIM_STATE_BUSY; - } - } - else - { - /* nothing to do */ - } - /* Enable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ - TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); - - /* Set the DMA Input Capture 1 Callbacks */ - htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; - htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt; - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - - /* Enable the DMA stream for Capture 1*/ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length) != HAL_OK) - { - return HAL_ERROR; - } - /* Enable the capture compare 1 Interrupt */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the TIM Hall Sensor Interface in DMA mode. - * @param htim TIM Hall Sensor Interface handle - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim) -{ - /* Check the parameters */ - assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - - /* Disable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ - TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); - - - /* Disable the capture compare Interrupts 1 event */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); - - (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - +HAL_StatusTypeDef SDIO_Init(SDIO_TypeDef *SDIOx, SDIO_InitTypeDef Init); /** * @} */ - -/** @defgroup TIMEx_Exported_Functions_Group2 Extended Timer Complementary Output Compare functions - * @brief Timer Complementary Output Compare functions - * -@verbatim - ============================================================================== - ##### Timer Complementary Output Compare functions ##### - ============================================================================== - [..] - This section provides functions allowing to: - (+) Start the Complementary Output Compare/PWM. - (+) Stop the Complementary Output Compare/PWM. - (+) Start the Complementary Output Compare/PWM and enable interrupts. - (+) Stop the Complementary Output Compare/PWM and disable interrupts. - (+) Start the Complementary Output Compare/PWM and enable DMA transfers. - (+) Stop the Complementary Output Compare/PWM and disable DMA transfers. - -@endverbatim + +/* I/O operation functions *****************************************************/ +/** @addtogroup HAL_SDMMC_LL_Group2 * @{ */ - -/** - * @brief Starts the TIM Output Compare signal generation on the complementary - * output. - * @param htim TIM Output Compare handle - * @param Channel TIM Channel to be enabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - /* Enable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the TIM Output Compare signal generation on the complementary - * output. - * @param htim TIM handle - * @param Channel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - /* Disable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Starts the TIM Output Compare signal generation in interrupt mode - * on the complementary output. - * @param htim TIM OC handle - * @param Channel TIM Channel to be enabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - switch (Channel) - { - case TIM_CHANNEL_1: - { - /* Enable the TIM Output Compare interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); - break; - } - - case TIM_CHANNEL_2: - { - /* Enable the TIM Output Compare interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); - break; - } - - case TIM_CHANNEL_3: - { - /* Enable the TIM Output Compare interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); - break; - } - - - default: - break; - } - - /* Enable the TIM Break interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK); - - /* Enable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the TIM Output Compare signal generation in interrupt mode - * on the complementary output. - * @param htim TIM Output Compare handle - * @param Channel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - uint32_t tmpccer; - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - switch (Channel) - { - case TIM_CHANNEL_1: - { - /* Disable the TIM Output Compare interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); - break; - } - - case TIM_CHANNEL_2: - { - /* Disable the TIM Output Compare interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); - break; - } - - case TIM_CHANNEL_3: - { - /* Disable the TIM Output Compare interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); - break; - } - - default: - break; - } - - /* Disable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - - /* Disable the TIM Break interrupt (only if no more channel is active) */ - tmpccer = htim->Instance->CCER; - if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET) - { - __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK); - } - - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Starts the TIM Output Compare signal generation in DMA mode - * on the complementary output. - * @param htim TIM Output Compare handle - * @param Channel TIM Channel to be enabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @param pData The source Buffer address. - * @param Length The length of data to be transferred from memory to TIM peripheral - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - if (htim->State == HAL_TIM_STATE_BUSY) - { - return HAL_BUSY; - } - else if (htim->State == HAL_TIM_STATE_READY) - { - if (((uint32_t)pData == 0U) && (Length > 0U)) - { - return HAL_ERROR; - } - else - { - htim->State = HAL_TIM_STATE_BUSY; - } - } - else - { - /* nothing to do */ - } - - switch (Channel) - { - case TIM_CHANNEL_1: - { - /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; - htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; - - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - - /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK) - { - return HAL_ERROR; - } - /* Enable the TIM Output Compare DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); - break; - } - - case TIM_CHANNEL_2: - { - /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; - htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; - - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - - /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK) - { - return HAL_ERROR; - } - /* Enable the TIM Output Compare DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); - break; - } - - case TIM_CHANNEL_3: - { - /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; - htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; - - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - - /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK) - { - return HAL_ERROR; - } - /* Enable the TIM Output Compare DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); - break; - } - - default: - break; - } - - /* Enable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the TIM Output Compare signal generation in DMA mode - * on the complementary output. - * @param htim TIM Output Compare handle - * @param Channel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - switch (Channel) - { - case TIM_CHANNEL_1: - { - /* Disable the TIM Output Compare DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); - (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); - break; - } - - case TIM_CHANNEL_2: - { - /* Disable the TIM Output Compare DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); - (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); - break; - } - - case TIM_CHANNEL_3: - { - /* Disable the TIM Output Compare DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); - (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); - break; - } - - default: - break; - } - - /* Disable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Change the htim state */ - htim->State = HAL_TIM_STATE_READY; - - /* Return function status */ - return HAL_OK; -} - +uint32_t SDIO_ReadFIFO(SDIO_TypeDef *SDIOx); +HAL_StatusTypeDef SDIO_WriteFIFO(SDIO_TypeDef *SDIOx, uint32_t *pWriteData); /** * @} */ - -/** @defgroup TIMEx_Exported_Functions_Group3 Extended Timer Complementary PWM functions - * @brief Timer Complementary PWM functions - * -@verbatim - ============================================================================== - ##### Timer Complementary PWM functions ##### - ============================================================================== - [..] - This section provides functions allowing to: - (+) Start the Complementary PWM. - (+) Stop the Complementary PWM. - (+) Start the Complementary PWM and enable interrupts. - (+) Stop the Complementary PWM and disable interrupts. - (+) Start the Complementary PWM and enable DMA transfers. - (+) Stop the Complementary PWM and disable DMA transfers. - (+) Start the Complementary Input Capture measurement. - (+) Stop the Complementary Input Capture. - (+) Start the Complementary Input Capture and enable interrupts. - (+) Stop the Complementary Input Capture and disable interrupts. - (+) Start the Complementary Input Capture and enable DMA transfers. - (+) Stop the Complementary Input Capture and disable DMA transfers. - (+) Start the Complementary One Pulse generation. - (+) Stop the Complementary One Pulse. - (+) Start the Complementary One Pulse and enable interrupts. - (+) Stop the Complementary One Pulse and disable interrupts. - -@endverbatim + +/* Peripheral Control functions ************************************************/ +/** @addtogroup HAL_SDMMC_LL_Group3 * @{ */ +HAL_StatusTypeDef SDIO_PowerState_ON(SDIO_TypeDef *SDIOx); +HAL_StatusTypeDef SDIO_PowerState_OFF(SDIO_TypeDef *SDIOx); +uint32_t SDIO_GetPowerState(SDIO_TypeDef *SDIOx); + +/* Command path state machine (CPSM) management functions */ +HAL_StatusTypeDef SDIO_SendCommand(SDIO_TypeDef *SDIOx, SDIO_CmdInitTypeDef *Command); +uint8_t SDIO_GetCommandResponse(SDIO_TypeDef *SDIOx); +uint32_t SDIO_GetResponse(SDIO_TypeDef *SDIOx, uint32_t Response); + +/* Data path state machine (DPSM) management functions */ +HAL_StatusTypeDef SDIO_ConfigData(SDIO_TypeDef *SDIOx, SDIO_DataInitTypeDef* Data); +uint32_t SDIO_GetDataCounter(SDIO_TypeDef *SDIOx); +uint32_t SDIO_GetFIFOCount(SDIO_TypeDef *SDIOx); + +/* SDMMC Cards mode management functions */ +HAL_StatusTypeDef SDIO_SetSDMMCReadWaitMode(SDIO_TypeDef *SDIOx, uint32_t SDIO_ReadWaitMode); + +/* SDMMC Commands management functions */ +uint32_t SDMMC_CmdBlockLength(SDIO_TypeDef *SDIOx, uint32_t BlockSize); +uint32_t SDMMC_CmdReadSingleBlock(SDIO_TypeDef *SDIOx, uint32_t ReadAdd); +uint32_t SDMMC_CmdReadMultiBlock(SDIO_TypeDef *SDIOx, uint32_t ReadAdd); +uint32_t SDMMC_CmdWriteSingleBlock(SDIO_TypeDef *SDIOx, uint32_t WriteAdd); +uint32_t SDMMC_CmdWriteMultiBlock(SDIO_TypeDef *SDIOx, uint32_t WriteAdd); +uint32_t SDMMC_CmdEraseStartAdd(SDIO_TypeDef *SDIOx, uint32_t StartAdd); +uint32_t SDMMC_CmdSDEraseStartAdd(SDIO_TypeDef *SDIOx, uint32_t StartAdd); +uint32_t SDMMC_CmdEraseEndAdd(SDIO_TypeDef *SDIOx, uint32_t EndAdd); +uint32_t SDMMC_CmdSDEraseEndAdd(SDIO_TypeDef *SDIOx, uint32_t EndAdd); +uint32_t SDMMC_CmdErase(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdStopTransfer(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdSelDesel(SDIO_TypeDef *SDIOx, uint64_t Addr); +uint32_t SDMMC_CmdGoIdleState(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdOperCond(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdAppCommand(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdAppOperCommand(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdBusWidth(SDIO_TypeDef *SDIOx, uint32_t BusWidth); +uint32_t SDMMC_CmdSendSCR(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdSendCID(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdSendCSD(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdSetRelAdd(SDIO_TypeDef *SDIOx, uint16_t *pRCA); +uint32_t SDMMC_CmdSendStatus(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdStatusRegister(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdOpCondition(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdSwitch(SDIO_TypeDef *SDIOx, uint32_t Argument); /** - * @brief Starts the PWM signal generation on the complementary output. - * @param htim TIM handle - * @param Channel TIM Channel to be enabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status + * @} */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - /* Enable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - + /** - * @brief Stops the PWM signal generation on the complementary output. - * @param htim TIM handle - * @param Channel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status + * @} */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - /* Disable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - + /** - * @brief Starts the PWM signal generation in interrupt mode on the - * complementary output. - * @param htim TIM handle - * @param Channel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - switch (Channel) - { - case TIM_CHANNEL_1: - { - /* Enable the TIM Capture/Compare 1 interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); - break; - } - - case TIM_CHANNEL_2: - { - /* Enable the TIM Capture/Compare 2 interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); - break; - } - - case TIM_CHANNEL_3: - { - /* Enable the TIM Capture/Compare 3 interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); - break; - } - - default: - break; - } - - /* Enable the TIM Break interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK); - - /* Enable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the PWM signal generation in interrupt mode on the - * complementary output. - * @param htim TIM handle - * @param Channel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - uint32_t tmpccer; - - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - switch (Channel) - { - case TIM_CHANNEL_1: - { - /* Disable the TIM Capture/Compare 1 interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); - break; - } - - case TIM_CHANNEL_2: - { - /* Disable the TIM Capture/Compare 2 interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); - break; - } - - case TIM_CHANNEL_3: - { - /* Disable the TIM Capture/Compare 3 interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); - break; - } - - default: - break; - } - - /* Disable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - - /* Disable the TIM Break interrupt (only if no more channel is active) */ - tmpccer = htim->Instance->CCER; - if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET) - { - __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK); - } - - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Starts the TIM PWM signal generation in DMA mode on the - * complementary output - * @param htim TIM handle - * @param Channel TIM Channel to be enabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @param pData The source Buffer address. - * @param Length The length of data to be transferred from memory to TIM peripheral - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) -{ - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - if (htim->State == HAL_TIM_STATE_BUSY) - { - return HAL_BUSY; - } - else if (htim->State == HAL_TIM_STATE_READY) - { - if (((uint32_t)pData == 0U) && (Length > 0U)) - { - return HAL_ERROR; - } - else - { - htim->State = HAL_TIM_STATE_BUSY; - } - } - else - { - /* nothing to do */ - } - switch (Channel) - { - case TIM_CHANNEL_1: - { - /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; - htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; - - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; - - /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK) - { - return HAL_ERROR; - } - /* Enable the TIM Capture/Compare 1 DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); - break; - } - - case TIM_CHANNEL_2: - { - /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; - htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; - - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; - - /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK) - { - return HAL_ERROR; - } - /* Enable the TIM Capture/Compare 2 DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); - break; - } - - case TIM_CHANNEL_3: - { - /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; - htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; - - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; - - /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK) - { - return HAL_ERROR; - } - /* Enable the TIM Capture/Compare 3 DMA request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); - break; - } - - default: - break; - } - - /* Enable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); - - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); - } - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the TIM PWM signal generation in DMA mode on the complementary - * output - * @param htim TIM handle - * @param Channel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @arg TIM_CHANNEL_3: TIM Channel 3 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) -{ - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - - switch (Channel) - { - case TIM_CHANNEL_1: - { - /* Disable the TIM Capture/Compare 1 DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); - (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); - break; - } - - case TIM_CHANNEL_2: - { - /* Disable the TIM Capture/Compare 2 DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); - (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]); - break; - } - - case TIM_CHANNEL_3: - { - /* Disable the TIM Capture/Compare 3 DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); - (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]); - break; - } - - default: - break; - } - - /* Disable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Change the htim state */ - htim->State = HAL_TIM_STATE_READY; - - /* Return function status */ - return HAL_OK; -} + * @} + */ /** * @} */ -/** @defgroup TIMEx_Exported_Functions_Group4 Extended Timer Complementary One Pulse functions - * @brief Timer Complementary One Pulse functions - * -@verbatim - ============================================================================== - ##### Timer Complementary One Pulse functions ##### - ============================================================================== - [..] - This section provides functions allowing to: - (+) Start the Complementary One Pulse generation. - (+) Stop the Complementary One Pulse. - (+) Start the Complementary One Pulse and enable interrupts. - (+) Stop the Complementary One Pulse and disable interrupts. - -@endverbatim - * @{ - */ - -/** - * @brief Starts the TIM One Pulse signal generation on the complementary - * output. - * @param htim TIM One Pulse handle - * @param OutputChannel TIM Channel to be enabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel) -{ - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); - - /* Enable the complementary One Pulse output */ - TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE); - - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); - - /* Return function status */ - return HAL_OK; +#ifdef __cplusplus } +#endif -/** - * @brief Stops the TIM One Pulse signal generation on the complementary - * output. - * @param htim TIM One Pulse handle - * @param OutputChannel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel) -{ - - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); - - /* Disable the complementary One Pulse output */ - TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE); - - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Starts the TIM One Pulse signal generation in interrupt mode on the - * complementary channel. - * @param htim TIM One Pulse handle - * @param OutputChannel TIM Channel to be enabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel) -{ - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); - - /* Enable the TIM Capture/Compare 1 interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); - - /* Enable the TIM Capture/Compare 2 interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); - - /* Enable the complementary One Pulse output */ - TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE); - - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); - - /* Return function status */ - return HAL_OK; -} - -/** - * @brief Stops the TIM One Pulse signal generation in interrupt mode on the - * complementary channel. - * @param htim TIM One Pulse handle - * @param OutputChannel TIM Channel to be disabled - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 selected - * @arg TIM_CHANNEL_2: TIM Channel 2 selected - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel) -{ - /* Check the parameters */ - assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); - - /* Disable the TIM Capture/Compare 1 interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); - - /* Disable the TIM Capture/Compare 2 interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); - - /* Disable the complementary One Pulse output */ - TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE); - - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); - - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); - - /* Return function status */ - return HAL_OK; -} - -/** - * @} - */ - -/** @defgroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions - * @brief Peripheral Control functions - * -@verbatim - ============================================================================== - ##### Peripheral Control functions ##### - ============================================================================== - [..] - This section provides functions allowing to: - (+) Configure the commutation event in case of use of the Hall sensor interface. - (+) Configure Output channels for OC and PWM mode. - - (+) Configure Complementary channels, break features and dead time. - (+) Configure Master synchronization. - (+) Configure timer remapping capabilities. - -@endverbatim - * @{ - */ - -/** - * @brief Configure the TIM commutation event sequence. - * @note This function is mandatory to use the commutation event in order to - * update the configuration at each commutation detection on the TRGI input of the Timer, - * the typical use of this feature is with the use of another Timer(interface Timer) - * configured in Hall sensor interface, this interface Timer will generate the - * commutation at its TRGO output (connected to Timer used in this function) each time - * the TI1 of the Interface Timer detect a commutation at its input TI1. - * @param htim TIM handle - * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor - * This parameter can be one of the following values: - * @arg TIM_TS_ITR0: Internal trigger 0 selected - * @arg TIM_TS_ITR1: Internal trigger 1 selected - * @arg TIM_TS_ITR2: Internal trigger 2 selected - * @arg TIM_TS_ITR3: Internal trigger 3 selected - * @arg TIM_TS_NONE: No trigger is needed - * @param CommutationSource the Commutation Event source - * This parameter can be one of the following values: - * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer - * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent(TIM_HandleTypeDef *htim, uint32_t InputTrigger, - uint32_t CommutationSource) -{ - /* Check the parameters */ - assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance)); - assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger)); - - __HAL_LOCK(htim); - - if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) || - (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3)) - { - /* Select the Input trigger */ - htim->Instance->SMCR &= ~TIM_SMCR_TS; - htim->Instance->SMCR |= InputTrigger; - } - - /* Select the Capture Compare preload feature */ - htim->Instance->CR2 |= TIM_CR2_CCPC; - /* Select the Commutation event source */ - htim->Instance->CR2 &= ~TIM_CR2_CCUS; - htim->Instance->CR2 |= CommutationSource; - - /* Disable Commutation Interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_COM); - - /* Disable Commutation DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_COM); - - __HAL_UNLOCK(htim); - - return HAL_OK; -} - -/** - * @brief Configure the TIM commutation event sequence with interrupt. - * @note This function is mandatory to use the commutation event in order to - * update the configuration at each commutation detection on the TRGI input of the Timer, - * the typical use of this feature is with the use of another Timer(interface Timer) - * configured in Hall sensor interface, this interface Timer will generate the - * commutation at its TRGO output (connected to Timer used in this function) each time - * the TI1 of the Interface Timer detect a commutation at its input TI1. - * @param htim TIM handle - * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor - * This parameter can be one of the following values: - * @arg TIM_TS_ITR0: Internal trigger 0 selected - * @arg TIM_TS_ITR1: Internal trigger 1 selected - * @arg TIM_TS_ITR2: Internal trigger 2 selected - * @arg TIM_TS_ITR3: Internal trigger 3 selected - * @arg TIM_TS_NONE: No trigger is needed - * @param CommutationSource the Commutation Event source - * This parameter can be one of the following values: - * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer - * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_IT(TIM_HandleTypeDef *htim, uint32_t InputTrigger, - uint32_t CommutationSource) -{ - /* Check the parameters */ - assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance)); - assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger)); - - __HAL_LOCK(htim); - - if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) || - (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3)) - { - /* Select the Input trigger */ - htim->Instance->SMCR &= ~TIM_SMCR_TS; - htim->Instance->SMCR |= InputTrigger; - } - - /* Select the Capture Compare preload feature */ - htim->Instance->CR2 |= TIM_CR2_CCPC; - /* Select the Commutation event source */ - htim->Instance->CR2 &= ~TIM_CR2_CCUS; - htim->Instance->CR2 |= CommutationSource; - - /* Disable Commutation DMA request */ - __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_COM); - - /* Enable the Commutation Interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_COM); - - __HAL_UNLOCK(htim); - - return HAL_OK; -} - -/** - * @brief Configure the TIM commutation event sequence with DMA. - * @note This function is mandatory to use the commutation event in order to - * update the configuration at each commutation detection on the TRGI input of the Timer, - * the typical use of this feature is with the use of another Timer(interface Timer) - * configured in Hall sensor interface, this interface Timer will generate the - * commutation at its TRGO output (connected to Timer used in this function) each time - * the TI1 of the Interface Timer detect a commutation at its input TI1. - * @note The user should configure the DMA in his own software, in This function only the COMDE bit is set - * @param htim TIM handle - * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor - * This parameter can be one of the following values: - * @arg TIM_TS_ITR0: Internal trigger 0 selected - * @arg TIM_TS_ITR1: Internal trigger 1 selected - * @arg TIM_TS_ITR2: Internal trigger 2 selected - * @arg TIM_TS_ITR3: Internal trigger 3 selected - * @arg TIM_TS_NONE: No trigger is needed - * @param CommutationSource the Commutation Event source - * This parameter can be one of the following values: - * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer - * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_DMA(TIM_HandleTypeDef *htim, uint32_t InputTrigger, - uint32_t CommutationSource) -{ - /* Check the parameters */ - assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance)); - assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger)); - - __HAL_LOCK(htim); - - if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) || - (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3)) - { - /* Select the Input trigger */ - htim->Instance->SMCR &= ~TIM_SMCR_TS; - htim->Instance->SMCR |= InputTrigger; - } - - /* Select the Capture Compare preload feature */ - htim->Instance->CR2 |= TIM_CR2_CCPC; - /* Select the Commutation event source */ - htim->Instance->CR2 &= ~TIM_CR2_CCUS; - htim->Instance->CR2 |= CommutationSource; - - /* Enable the Commutation DMA Request */ - /* Set the DMA Commutation Callback */ - htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; - htim->hdma[TIM_DMA_ID_COMMUTATION]->XferHalfCpltCallback = TIMEx_DMACommutationHalfCplt; - /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError; - - /* Disable Commutation Interrupt */ - __HAL_TIM_DISABLE_IT(htim, TIM_IT_COM); - - /* Enable the Commutation DMA Request */ - __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_COM); - - __HAL_UNLOCK(htim); - - return HAL_OK; -} - -/** - * @brief Configures the TIM in master mode. - * @param htim TIM handle. - * @param sMasterConfig pointer to a TIM_MasterConfigTypeDef structure that - * contains the selected trigger output (TRGO) and the Master/Slave - * mode. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim, - TIM_MasterConfigTypeDef *sMasterConfig) -{ - uint32_t tmpcr2; - uint32_t tmpsmcr; - - /* Check the parameters */ - assert_param(IS_TIM_MASTER_INSTANCE(htim->Instance)); - assert_param(IS_TIM_TRGO_SOURCE(sMasterConfig->MasterOutputTrigger)); - assert_param(IS_TIM_MSM_STATE(sMasterConfig->MasterSlaveMode)); - - /* Check input state */ - __HAL_LOCK(htim); - - /* Change the handler state */ - htim->State = HAL_TIM_STATE_BUSY; - - /* Get the TIMx CR2 register value */ - tmpcr2 = htim->Instance->CR2; - - /* Get the TIMx SMCR register value */ - tmpsmcr = htim->Instance->SMCR; - - /* Reset the MMS Bits */ - tmpcr2 &= ~TIM_CR2_MMS; - /* Select the TRGO source */ - tmpcr2 |= sMasterConfig->MasterOutputTrigger; - - /* Reset the MSM Bit */ - tmpsmcr &= ~TIM_SMCR_MSM; - /* Set master mode */ - tmpsmcr |= sMasterConfig->MasterSlaveMode; - - /* Update TIMx CR2 */ - htim->Instance->CR2 = tmpcr2; - - /* Update TIMx SMCR */ - htim->Instance->SMCR = tmpsmcr; - - /* Change the htim state */ - htim->State = HAL_TIM_STATE_READY; - - __HAL_UNLOCK(htim); - - return HAL_OK; -} - -/** - * @brief Configures the Break feature, dead time, Lock level, OSSI/OSSR State - * and the AOE(automatic output enable). - * @param htim TIM handle - * @param sBreakDeadTimeConfig pointer to a TIM_ConfigBreakDeadConfigTypeDef structure that - * contains the BDTR Register configuration information for the TIM peripheral. - * @note Interrupts can be generated when an active level is detected on the - * break input, the break 2 input or the system break input. Break - * interrupt can be enabled by calling the @ref __HAL_TIM_ENABLE_IT macro. - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim, - TIM_BreakDeadTimeConfigTypeDef *sBreakDeadTimeConfig) -{ - /* Keep this variable initialized to 0 as it is used to configure BDTR register */ - uint32_t tmpbdtr = 0U; - - /* Check the parameters */ - assert_param(IS_TIM_BREAK_INSTANCE(htim->Instance)); - assert_param(IS_TIM_OSSR_STATE(sBreakDeadTimeConfig->OffStateRunMode)); - assert_param(IS_TIM_OSSI_STATE(sBreakDeadTimeConfig->OffStateIDLEMode)); - assert_param(IS_TIM_LOCK_LEVEL(sBreakDeadTimeConfig->LockLevel)); - assert_param(IS_TIM_DEADTIME(sBreakDeadTimeConfig->DeadTime)); - assert_param(IS_TIM_BREAK_STATE(sBreakDeadTimeConfig->BreakState)); - assert_param(IS_TIM_BREAK_POLARITY(sBreakDeadTimeConfig->BreakPolarity)); - assert_param(IS_TIM_AUTOMATIC_OUTPUT_STATE(sBreakDeadTimeConfig->AutomaticOutput)); - - /* Check input state */ - __HAL_LOCK(htim); - - /* Set the Lock level, the Break enable Bit and the Polarity, the OSSR State, - the OSSI State, the dead time value and the Automatic Output Enable Bit */ - - /* Set the BDTR bits */ - MODIFY_REG(tmpbdtr, TIM_BDTR_DTG, sBreakDeadTimeConfig->DeadTime); - MODIFY_REG(tmpbdtr, TIM_BDTR_LOCK, sBreakDeadTimeConfig->LockLevel); - MODIFY_REG(tmpbdtr, TIM_BDTR_OSSI, sBreakDeadTimeConfig->OffStateIDLEMode); - MODIFY_REG(tmpbdtr, TIM_BDTR_OSSR, sBreakDeadTimeConfig->OffStateRunMode); - MODIFY_REG(tmpbdtr, TIM_BDTR_BKE, sBreakDeadTimeConfig->BreakState); - MODIFY_REG(tmpbdtr, TIM_BDTR_BKP, sBreakDeadTimeConfig->BreakPolarity); - MODIFY_REG(tmpbdtr, TIM_BDTR_AOE, sBreakDeadTimeConfig->AutomaticOutput); - - - /* Set TIMx_BDTR */ - htim->Instance->BDTR = tmpbdtr; - - __HAL_UNLOCK(htim); - - return HAL_OK; -} - -/** - * @brief Configures the TIMx Remapping input capabilities. - * @param htim TIM handle. - * @param Remap specifies the TIM remapping source. - * For TIM2, the parameter can have the following values: - * @arg TIM_TIM2_TIM8_TRGO: TIM2 ITR1 is connected to TIM8 TRGO - * @arg TIM_TIM2_ETH_PTP: TIM2 ITR1 is connected to PTP trigger output - * @arg TIM_TIM2_USBFS_SOF: TIM2 ITR1 is connected to OTG FS SOF - * @arg TIM_TIM2_USBHS_SOF: TIM2 ITR1 is connected to OTG FS SOF - * - * For TIM5, the parameter can have the following values: - * @arg TIM_TIM5_GPIO: TIM5 TI4 is connected to GPIO - * @arg TIM_TIM5_LSI: TIM5 TI4 is connected to LSI - * @arg TIM_TIM5_LSE: TIM5 TI4 is connected to LSE - * @arg TIM_TIM5_RTC: TIM5 TI4 is connected to the RTC wakeup interrupt - * - * For TIM11, the parameter can have the following values: - * @arg TIM_TIM11_GPIO: TIM11 TI1 is connected to GPIO - * @arg TIM_TIM11_HSE: TIM11 TI1 is connected to HSE_RTC clock - * - * @retval HAL status - */ -HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap) -{ - __HAL_LOCK(htim); - - /* Check parameters */ - assert_param(IS_TIM_REMAP(htim->Instance, Remap)); - - /* Set the Timer remapping configuration */ - WRITE_REG(htim->Instance->OR, Remap); - - __HAL_UNLOCK(htim); - - return HAL_OK; -} - -/** - * @} - */ - -/** @defgroup TIMEx_Exported_Functions_Group6 Extended Callbacks functions - * @brief Extended Callbacks functions - * -@verbatim - ============================================================================== - ##### Extended Callbacks functions ##### - ============================================================================== - [..] - This section provides Extended TIM callback functions: - (+) Timer Commutation callback - (+) Timer Break callback - -@endverbatim - * @{ - */ - -/** - * @brief Hall commutation changed callback in non-blocking mode - * @param htim TIM handle - * @retval None - */ -__weak void HAL_TIMEx_CommutCallback(TIM_HandleTypeDef *htim) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(htim); - - /* NOTE : This function should not be modified, when the callback is needed, - the HAL_TIMEx_CommutCallback could be implemented in the user file - */ -} -/** - * @brief Hall commutation changed half complete callback in non-blocking mode - * @param htim TIM handle - * @retval None - */ -__weak void HAL_TIMEx_CommutHalfCpltCallback(TIM_HandleTypeDef *htim) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(htim); - - /* NOTE : This function should not be modified, when the callback is needed, - the HAL_TIMEx_CommutHalfCpltCallback could be implemented in the user file - */ -} - -/** - * @brief Hall Break detection callback in non-blocking mode - * @param htim TIM handle - * @retval None - */ -__weak void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef *htim) -{ - /* Prevent unused argument(s) compilation warning */ - UNUSED(htim); - - /* NOTE : This function should not be modified, when the callback is needed, - the HAL_TIMEx_BreakCallback could be implemented in the user file - */ -} -/** - * @} - */ - -/** @defgroup TIMEx_Exported_Functions_Group7 Extended Peripheral State functions - * @brief Extended Peripheral State functions - * -@verbatim - ============================================================================== - ##### Extended Peripheral State functions ##### - ============================================================================== - [..] - This subsection permits to get in run-time the status of the peripheral - and the data flow. - -@endverbatim - * @{ - */ - -/** - * @brief Return the TIM Hall Sensor interface handle state. - * @param htim TIM Hall Sensor handle - * @retval HAL state - */ -HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim) -{ - return htim->State; -} - -/** - * @} - */ - -/** - * @} - */ - -/* Private functions ---------------------------------------------------------*/ -/** @defgroup TIMEx_Private_Functions TIMEx Private Functions - * @{ - */ - -/** - * @brief TIM DMA Commutation callback. - * @param hdma pointer to DMA handle. - * @retval None - */ -void TIMEx_DMACommutationCplt(DMA_HandleTypeDef *hdma) -{ - TIM_HandleTypeDef *htim = (TIM_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; - - /* Change the htim state */ - htim->State = HAL_TIM_STATE_READY; - -#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) - htim->CommutationCallback(htim); -#else - HAL_TIMEx_CommutCallback(htim); -#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ -} - -/** - * @brief TIM DMA Commutation half complete callback. - * @param hdma pointer to DMA handle. - * @retval None - */ -void TIMEx_DMACommutationHalfCplt(DMA_HandleTypeDef *hdma) -{ - TIM_HandleTypeDef *htim = (TIM_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; - - /* Change the htim state */ - htim->State = HAL_TIM_STATE_READY; - -#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) - htim->CommutationHalfCpltCallback(htim); -#else - HAL_TIMEx_CommutHalfCpltCallback(htim); -#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ -} - - -/** - * @brief Enables or disables the TIM Capture Compare Channel xN. - * @param TIMx to select the TIM peripheral - * @param Channel specifies the TIM Channel - * This parameter can be one of the following values: - * @arg TIM_CHANNEL_1: TIM Channel 1 - * @arg TIM_CHANNEL_2: TIM Channel 2 - * @arg TIM_CHANNEL_3: TIM Channel 3 - * @param ChannelNState specifies the TIM Channel CCxNE bit new state. - * This parameter can be: TIM_CCxN_ENABLE or TIM_CCxN_Disable. - * @retval None - */ -static void TIM_CCxNChannelCmd(TIM_TypeDef *TIMx, uint32_t Channel, uint32_t ChannelNState) -{ - uint32_t tmp; - - tmp = TIM_CCER_CC1NE << (Channel & 0x1FU); /* 0x1FU = 31 bits max shift */ - - /* Reset the CCxNE Bit */ - TIMx->CCER &= ~tmp; - - /* Set or reset the CCxNE Bit */ - TIMx->CCER |= (uint32_t)(ChannelNState << (Channel & 0x1FU)); /* 0x1FU = 31 bits max shift */ -} -/** - * @} - */ - -#endif /* HAL_TIM_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ +#endif /* STM32F2xx_LL_SDMMC_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/