mirror of
https://github.com/STMicroelectronics/STM32CubeF1.git
synced 2025-05-10 19:29:19 +08:00
68 lines
2.8 KiB
Plaintext
68 lines
2.8 KiB
Plaintext
/**
|
|
@page UTILS_ConfigureSystemClock UTILS example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file Examples_LL/UTILS/UTILS_ConfigureSystemClock/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the UTILS example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example describes how to use UTILS LL API to configure the system clock using PLL with HSI as source
|
|
clock. The user application just needs to calculate PLL parameters using STM32CubeMX and call the UTILS LL
|
|
API.
|
|
|
|
System starts with clock used after reset.
|
|
Then, a system clock switch is done to PLL with HSI as PLL clock source. Automatically, FLASH latency
|
|
is tuned according to system constraints described in the reference manual.
|
|
|
|
User can easily set its own PLL parameters in changing global variable used to store them.
|
|
|
|
A LED2 toggle of 1sec provides this information that system is well configured to requested frequency.
|
|
|
|
Anyway, signal on PA.08 can be monitored with an oscilloscope (in connecting PA.08 to pin 23 of CN10)
|
|
to check the requested frequency:
|
|
- SYSCLK frequency with frequency value around @64MHz.
|
|
|
|
@par Directory contents
|
|
|
|
- UTILS/UTILS_ConfigureSystemClock/Inc/stm32f1xx_it.h Interrupt handlers header file
|
|
- UTILS/UTILS_ConfigureSystemClock/Inc/main.h Header for main.c module
|
|
- UTILS/UTILS_ConfigureSystemClock/Inc/stm32_assert.h Template file to include assert_failed function
|
|
- UTILS/UTILS_ConfigureSystemClock/Src/stm32f1xx_it.c Interrupt handlers
|
|
- UTILS/UTILS_ConfigureSystemClock/Src/main.c Main program
|
|
- UTILS/UTILS_ConfigureSystemClock/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F103xB devices.
|
|
|
|
- This example has been tested with STM32F103RB-Nucleo board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|