mirror of
https://github.com/STMicroelectronics/STM32CubeF1.git
synced 2025-05-08 19:29:51 +08:00
136 lines
5.7 KiB
Plaintext
136 lines
5.7 KiB
Plaintext
/**
|
|
@page UART_HyperTerminal_DMA UART Hyperterminal DMA Example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file UART/UART_HyperTerminal_DMA/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the UART Hyperterminal example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
UART transmission (transmit/receive) in DMA mode
|
|
between a board and an HyperTerminal PC application.
|
|
|
|
Board: STM3210C-EVAL RevC
|
|
Tx Pin: PD.05
|
|
Rx Pin: PD.06
|
|
_________________________
|
|
| ______________| _______________
|
|
| |USART | | HyperTerminal |
|
|
| | | | |
|
|
| | TX |______________________|RX |
|
|
| | | | |
|
|
| | | RS232 Cable | |
|
|
| | | | |
|
|
| | RX |______________________|TX |
|
|
| | | | |
|
|
| |______________| |_______________|
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
|_STM32_Board_____________|
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system
|
|
clock (SYSCLK) to run at 72 MHz.
|
|
|
|
The UART peripheral configuration is ensured by the HAL_UART_Init() function.
|
|
This later is calling the HAL_UART_MspInit()function which core is implementing
|
|
the configuration of the needed UART resources according to the used hardware (CLOCK,
|
|
GPIO, DMA and NVIC). You may update this function to change UART configuration.
|
|
|
|
The UART/Hyperterminal communication is then initiated.
|
|
The HAL_UART_Receive_DMA() and the HAL_UART_Transmit_DMA() functions allow respectively
|
|
the reception of Data from Hyperterminal and the transmission of a predefined data
|
|
buffer.
|
|
|
|
The Asynchronous communication aspect of the UART is clearly highlighted as the
|
|
data buffers transmission/reception to/from Hyperterminal are done simultaneously.
|
|
|
|
For this example the TxBuffer is predefined and the RxBuffer size is limited to
|
|
10 data by the mean of the RXBUFFERSIZE define in the main.c file.
|
|
|
|
In a first step the received data will be stored in the RxBuffer buffer and the
|
|
TxBuffer buffer content will be displayed in the Hyperterminal interface.
|
|
In a second step the received data in the RxBuffer buffer will be sent back to
|
|
Hyperterminal and displayed.
|
|
The end of this two steps are monitored through the HAL_UART_GetState() function
|
|
result.
|
|
|
|
STM32 board's LEDs can be used to monitor the transfer status:
|
|
- LED1 is ON when the transmission process is complete.
|
|
- LED2 is ON when the reception process is complete.
|
|
- LED3 is ON when there is an error in transmission/reception process.
|
|
|
|
The UART is configured as follows:
|
|
- BaudRate = 9600 baud
|
|
- Word Length = 8 Bits (7 data bit + 1 parity bit)
|
|
- One Stop Bit
|
|
- Odd parity
|
|
- Hardware flow control disabled (RTS and CTS signals)
|
|
- Reception and transmission are enabled in the time
|
|
|
|
@note USARTx/UARTx instance used and associated resources can be updated in "main.h"
|
|
file depending hardware configuration used.
|
|
|
|
@note When the parity is enabled, the computed parity is inserted at the MSB
|
|
position of the transmitted data.
|
|
|
|
|
|
@par Directory contents
|
|
|
|
- UART/UART_HyperTerminal_DMA/Inc/stm32f1xx_hal_conf.h HAL configuration file
|
|
- UART/UART_HyperTerminal_DMA/Inc/stm32f1xx_it.h DMA interrupt handlers header file
|
|
- UART/UART_HyperTerminal_DMA/Inc/main.h Header for main.c module
|
|
- UART/UART_HyperTerminal_DMA/Src/stm32f1xx_it.c DMA interrupt handlers
|
|
- UART/UART_HyperTerminal_DMA/Src/main.c Main program
|
|
- UART/UART_HyperTerminal_DMA/Src/stm32f1xx_hal_msp.c HAL MSP module
|
|
- UART/UART_HyperTerminal_DMA/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F107xC devices.
|
|
|
|
- This example has been tested with STM3210C-EVAL RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM3210C_EVAL Set-up
|
|
- Connect a null-modem female/female RS232 cable between the DB9 connector
|
|
CN6 (USART2) and PC serial port if you want to display data on the HyperTerminal.
|
|
@note Make sure that jumper JP16 is 2-3 position (USART2_RX).
|
|
|
|
- Hyperterminal configuration:
|
|
- Word Length = 7 Bits
|
|
- One Stop Bit
|
|
- Odd parity
|
|
- BaudRate = 9600 baud
|
|
- flow control: None
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|