mirror of
https://github.com/STMicroelectronics/STM32CubeF1.git
synced 2025-05-10 19:29:19 +08:00
76 lines
3.2 KiB
Plaintext
76 lines
3.2 KiB
Plaintext
/**
|
|
@page DAC_SignalsGeneration DAC Signals generation example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file DAC/DAC_SignalsGeneration/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the DAC Signals generation example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to use the DAC peripheral to generate several signals using the DMA
|
|
controller.
|
|
|
|
For each press on Key push-button, a signal has been selected and can be monitored on
|
|
the DAC channel one:
|
|
- Triangle waveform (Channel 1).
|
|
- Escalator waveform (Channel 1) using DMA transfer.
|
|
|
|
STM3210C-EVAL RevC board's LEDs can be used to monitor the process status:
|
|
- LED3 is ON and example is stopped (using infinite loop)
|
|
when there is an error during process.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- DAC/DAC_SignalsGeneration/Inc/stm32f1xx_hal_conf.h HAL configuration file
|
|
- DAC/DAC_SignalsGeneration/Inc/stm32f1xx_it.h DAC interrupt handlers header file
|
|
- DAC/DAC_SignalsGeneration/Inc/main.h Header for main.c module
|
|
- DAC/DAC_SignalsGeneration/Src/stm32f1xx_it.c DAC interrupt handlers
|
|
- DAC/DAC_SignalsGeneration/Src/main.c Main program
|
|
- DAC/DAC_SignalsGeneration/Src/stm32f1xx_hal_msp.c HAL MSP file
|
|
- DAC/DAC_SignalsGeneration/Src/system_stm32f1xx.c STM32F1xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
- This example runs on STM32F1xx devices.
|
|
|
|
- This example has been tested with STM3210C-EVAL RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM3210C-EVAL RevC Set-up
|
|
- Use Key push-button connected to PB.09.
|
|
- Connect PA4 (DAC Channel1) (pin 41 in CN9) to an oscilloscope.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|
|
|