STM32CubeF1

@verbatim
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
* @file Examples_LL/I2C/I2C_OneBoard_Communication_PollingAndIT/readme.txt
* @author MCD Application Team
* @brief Description of the I2C_OneBoard_Communication_PollingAndIT I2C example (Master Polling Mode).
******************************************************************************
* @attention
*
* <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
@endverbatim

@par Example Description

How to transmit data bytes from an I2C master device using polling mode
to an I2C slave device using interrupt mode. The peripheral is initialized
with LL unitary service functions to optimize for performance and size.

This example guides you through the different configuration steps by mean of LL API
to configure GPIO and I2C peripherals using only one STM32F103RB-Nucleo.

I2C2 Peripheral is configured in Slave mode with EXTI (Clock 400Khz, Own address 7-bit enabled).
I2C1 Peripheral is configured in Master mode (Clock 400Khz).
GPIO associated to User push-button is linked with EXTI.

LED2 blinks quickly to wait for user-button press.

Example execution:
Press the User push-button to initiate a Start condition by Master.
This action will generate an I2C start condition on the I2C bus.
When the I2C start condition is sent on I2C1, a SB flag is raised.
This will allow Master to send the Slave address with a write bit condition.
When address Slave match code is received on I2C2, the Slave acknowledge the address.
When this acknowledge is received on I2C1, an ADDR flag is raised.

When address Slave match code is received on I2C2, an ADDR interrupt occurs.
I2C2 IRQ Handler routine is then checking Address Match Code and direction at Read (mean write direction for Master).
This will allow Slave to enter in receiver mode and then acknowledge Master to send the bytes.
When acknowledge is received on I2C1, a TXE event occurs.
This will allow Master to transmit a byte to the Slave.
Each time a byte is received on I2C2 (Slave), an RXNE interrupt occurs until a STOP condition.
And so each time the Slave acknowledge the byte received a TXE event occurs on Master side.
Master generate a Stop condition when size of data to transmit is achieved.

The STOP condition generate a STOP interrupt and initiate the end of reception on Slave side.
I2C2 IRQ handler routine is then clearing the STOP flag.

LED2 is On if data are well received.

In case of errors, LED2 is blinking.

@par Directory contents

- I2C/I2C_OneBoard_Communication_PollingAndIT/Inc/stm32f1xx_it.h Interrupt handlers header file
- I2C/I2C_OneBoard_Communication_PollingAndIT/Inc/main.h Header for main.c module
- I2C/I2C_OneBoard_Communication_PollingAndIT/Inc/stm32_assert.h Template file to include assert_failed function
- I2C/I2C_OneBoard_Communication_PollingAndIT/Src/stm32f1xx_it.c Interrupt handlers
- I2C/I2C_OneBoard_Communication_PollingAndIT/Src/main.c Main program
- I2C/I2C_OneBoard_Communication_PollingAndIT/Src/system_stm32f1xx.c STM32F1xx system source file

@par Hardware and Software environment

- This example runs on STM32F103xB devices.

- This example has been tested with STM32F103RB-Nucleo board and can be
easily tailored to any other supported device and development board.

- STM32F103RB-Nucleo Set-up
- Connect GPIOs connected to I2C2 SCL/SDA (PB.10 and PB.11)
to respectively SCL and SDA pins of I2C1 (PB.6 and PB.7).
- I2C2_SCL PB.10 (CN10, pin 25) : connected to I2C1_SCL PB.6 (CN10, pin 17)
- I2C2_SDA PB.11 (CN10, pin 18) : connected to I2C1_SDA PB.7 (CN7, pin 21)
- Check that a pull-up resistor (4.7K) is connected on one I2C SDA pin
- Check that a pull-up resistor (4.7K) is connected on one I2C SCL pin

- Launch the program. Press User push-button to initiate a write request by Master
then Slave receive bytes.

@par How to use it ?

In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example