mirror of
https://github.com/STMicroelectronics/STM32CubeF0.git
synced 2025-05-08 19:29:49 +08:00
93 lines
4.3 KiB
Plaintext
93 lines
4.3 KiB
Plaintext
/**
|
|
@page TSC_BasicAcquisition_Interrupt Touch-Sensing basic acquisition using interrupt
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file TSC/TSC_BasicAcquisition_Interrupt/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TSC basic acquisition interrupt example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Use of he TSC to perform continuous acquisitions
|
|
of two channels in Interrupt mode.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system
|
|
clock (SYSCLK) to run at 48 MHz.
|
|
|
|
The TSC peripheral configuration is ensured by the HAL_TSC_Init() function.
|
|
This later is calling the HAL_TSC_MspInit()function which core is implementing
|
|
the configuration of the needed TSC resources according to the used hardware (CLOCK,
|
|
GPIO and NVIC). You may update this function to change TSC configuration.
|
|
|
|
The TSC acquisition is then initiated.
|
|
When the end of acquisition occurs, the acquired data are affected to the
|
|
uhTSCAcquisitionValue[] variable.
|
|
Depending of value of uhTSCAcquisitionValue[] under the max threshold values,
|
|
the corresponding LEDs are set ON.
|
|
These max threshold values can be modified in top of main.c, due to disparity link to board layout quality.
|
|
|
|
STM32091C-EVAL's LEDs are used as follows:
|
|
- LED1 and LED2 show the touch activity for each channel.
|
|
- LED4 toggles when an error occurs (TSC initialization, TSC start or assert).
|
|
- LED3 is not used
|
|
|
|
@note TSCx instance used and associated resources can be updated in "main.h"
|
|
file depending hardware configuration used.
|
|
|
|
@note TSCx_TS1_MAXTHRESHOLD and TSCx_TS2_MAXTHRESHOLD can be modify if expected result is not satisfied.
|
|
These values are link to board layout quality.
|
|
To calibrate these value, need to check result of uhTSCAcquisitionValue[] when your digits is near or touch the sensor.
|
|
The new max threshold for each channel are around 1% under these values.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- TSC/TSC_BasicAcquisition_Interrupt/Inc/stm32f0xx_hal_conf.h HAL configuration file
|
|
- TSC/TSC_BasicAcquisition_Interrupt/Inc/stm32f0xx_it.h Interrupt handlers header file
|
|
- TSC/TSC_BasicAcquisition_Interrupt/Inc/main.h Header for main.c module
|
|
- TSC/TSC_BasicAcquisition_Interrupt/Src/stm32f0xx_it.c Interrupt handlers
|
|
- TSC/TSC_BasicAcquisition_Interrupt/Src/main.c Main program
|
|
- TSC/TSC_BasicAcquisition_Interrupt/Src/stm32f0xx_hal_msp.c HAL MSP file
|
|
- TSC/TSC_BasicAcquisition_Interrupt/Src/system_stm32f0xx.c STM32F0xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F091xC devices.
|
|
|
|
- This example has been tested with STM32091C-EVAL board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|