STM32CubeF0

@verbatim
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
* @file TIM/TIM_InputCapture/readme.txt
* @author MCD Application Team
* @brief Description of the TIM_InputCapture example.
******************************************************************************
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
@endverbatim

@par Example Description

Use of the TIM peripheral to measure an external signal frequency.

The TIM1CLK frequency is set to SystemCoreClock (Hz), the Prescaler is 0,
so the TIM1 counter clock is SystemCoreClock (Hz).
SystemCoreClock is set to 48 MHz for STM32F072xB Devices.

TIM1 is configured in Input Capture Mode: the external signal is connected to
TIM1 Channel2 used as input pin.
To measure the frequency we use the TIM1 CC2 interrupt request, so in the
TIM1_CC_IRQHandler routine, the frequency of the external signal is computed.

The "uwFrequency" variable contains the external signal frequency:
uwFrequency = TIM1 counter clock / uwDiffCapture (Hz),
where "uwDiffCapture" is the difference between two consecutive TIM1 captures.

The minimum frequency value to measure is TIM1 counter clock / CCR MAX
= 48 MHz / 65535

Due to TIM1_CC_IRQHandler processing time (around 5.25us), the maximum
frequency value to measure is around 190kHz.

@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.

@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.

@par Directory contents

- TIM/TIM_InputCapture/Inc/stm32f0xx_hal_conf.h HAL configuration file
- TIM/TIM_InputCapture/Inc/stm32f0xx_it.h Interrupt handlers header file
- TIM/TIM_InputCapture/Inc/main.h Header for main.c module
- TIM/TIM_InputCapture/Src/stm32f0xx_it.c Interrupt handlers
- TIM/TIM_InputCapture/Src/main.c Main program
- TIM/TIM_InputCapture/Src/stm32f0xx_hal_msp.c HAL MSP file
- TIM/TIM_InputCapture/Src/system_stm32f0xx.c STM32F0xx system source file

@par Hardware and Software environment

- This example runs on STM32F072xB devices.
- In this example, the clock is set to 48 MHz.

- This example has been tested with STMicroelectronics STM32F072B-Discovery RevC
board and can be easily tailored to any other supported device
and development board.

- STM32F072B-Discovery RevC Set-up
- Connect the external signal to measure to the TIM1 CH2 pin (PA.09).

@par How to use it ?

In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example