mirror of
https://github.com/STMicroelectronics/STM32CubeF0.git
synced 2025-05-03 22:17:10 +08:00
90 lines
3.7 KiB
Plaintext
90 lines
3.7 KiB
Plaintext
/**
|
|
@page FreeRTOS_Signal FreeRTOS Signal example
|
|
|
|
@verbatim
|
|
******************************************************************************
|
|
* @file FreeRTOS/FreeRTOS_Signal/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the FreeRTOS Signal example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under Ultimate Liberty license
|
|
* SLA0044, the "License"; You may not use this file except in compliance with
|
|
* the License. You may obtain a copy of the License at:
|
|
* www.st.com/SLA0044
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Application Description
|
|
|
|
How to perform thread signaling using CMSIS RTOS API.
|
|
|
|
This example creates three threads with the same priority.
|
|
|
|
Thread1 calls osSignalWait to wait for a signal that sets bit0, then toggles LED1
|
|
|
|
Thread2 calls osSignalWait to wait for a signal that sets bit1 and bit2, then toggles LED2
|
|
|
|
Thread3 performs the following actions:
|
|
- calls osSetSignal to send a signal with bit0 to Thread1
|
|
- delay for 500ms
|
|
- calls osSetSignal to send a signal with bit1 and bit2 to Thread2
|
|
- delay for 500ms
|
|
As a result, LEDs 1 and 2 show the following behaviour:
|
|
- LED1 On, delay 500ms
|
|
- LED2 On, delay 500ms
|
|
- LED1 Off, delay 500ms
|
|
- LED2 off, delay 500ms
|
|
- loop-back
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate
|
|
delay (in milliseconds) based on variable incremented in HAL time base ISR.
|
|
This implies that if HAL_Delay() is called from a peripheral ISR process, then
|
|
the HAL time base interrupt must have higher priority (numerically lower) than
|
|
the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the HAL time base interrupt priority you have to use HAL_NVIC_SetPriority()
|
|
function.
|
|
|
|
@note The application needs to ensure that the HAL time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@note The FreeRTOS heap size configTOTAL_HEAP_SIZE defined in FreeRTOSConfig.h is set accordingly to the
|
|
OS resources memory requirements of the application with +10% margin and rounded to the upper Kbyte boundary.
|
|
|
|
For more details about FreeRTOS implementation on STM32Cube, please refer to UM1722 "Developing Applications
|
|
on STM32Cube with RTOS".
|
|
|
|
|
|
@par Directory contents
|
|
- FreeRTOS/FreeRTOS_Signal/Src/main.c Main program
|
|
- FreeRTOS/FreeRTOS_Signal/Src/stm32f0xx_hal_timebase_tim.c HAL timebase file
|
|
- FreeRTOS/FreeRTOS_Signal/Src/stm32f0xx_it.c Interrupt handlers
|
|
- FreeRTOS/FreeRTOS_Signal/Src/system_stm32f0xx.c STM32F0xx system clock configuration file
|
|
- FreeRTOS/FreeRTOS_Signal/Inc/main.h Main program header file
|
|
- FreeRTOS/FreeRTOS_Signal/Inc/stm32f0xx_hal_conf.h HAL Library Configuration file
|
|
- FreeRTOS/FreeRTOS_Signal/Inc/stm32f0xx_it.h Interrupt handlers header file
|
|
- FreeRTOS/FreeRTOS_Signal/Inc/FreeRTOSConfig.h FreeRTOS Configuration file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F091xC devices.
|
|
|
|
- This example has been tested with STM32091C-EVAL board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following:
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|