mirror of
https://github.com/STMicroelectronics/STM32CubeF0.git
synced 2025-05-10 19:29:18 +08:00
67 lines
2.7 KiB
Plaintext
67 lines
2.7 KiB
Plaintext
/**
|
|
@page EEPROM_Emulation application to show an eeprom emulation
|
|
|
|
@verbatim
|
|
******************* (C) COPYRIGHT 2016 STMicroelectronics ********************
|
|
* @file EEPROM_Emulation/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the EEPROM_Emulation application.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under Ultimate Liberty license
|
|
* SLA0044, the "License"; You may not use this file except in compliance with
|
|
* the License. You may obtain a copy of the License at:
|
|
* www.st.com/SLA0044
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Application Description
|
|
|
|
This application shows how to emulate EEPROM on internal flash.
|
|
|
|
Please refer to AN4061 for futher details regarding this application.
|
|
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
|
|
- EEPROM_Emulation/Inc/stm32f0xx_hal_conf.h HAL Configuration file
|
|
- EEPROM_Emulation/Inc/eeprom.h Header for main.c module
|
|
- EEPROM_Emulation/Inc/stm32f0xx_it.h Header for stm32f0xx_it.c
|
|
- EEPROM_Emulation/Src/main.c Main program
|
|
- EEPROM_Emulation/Src/eeprom.c EEPROM program
|
|
- EEPROM_Emulation/Src/stm32f0xx_it.c Interrupt handlers
|
|
- EEPROM_Emulation/Src/system_stm32f0xx.c STM32F0xx system clock configuration file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F0xx devices.
|
|
|
|
- This example has been tested with STM32F091RC-Nucleo RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|