mirror of
https://github.com/STMicroelectronics/STM32CubeF0.git
synced 2025-05-08 19:29:49 +08:00
82 lines
3.3 KiB
Plaintext
82 lines
3.3 KiB
Plaintext
/**
|
|
@page TIM_InputCapture TIM example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file Examples_LL/TIM/TIM_InputCapture/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TIM_InputCapture example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Use of the TIM peripheral to measure a periodic signal frequency
|
|
provided either by an external signal generator or by
|
|
another timer instance. This example is based on the STM32F0xx TIM
|
|
LL API. The peripheral initialization uses LL unitary service functions
|
|
for optimization purposes (performance and size).
|
|
|
|
TIM1_CH1 is configured in input capture mode. The TIM1CLK frequency is set to
|
|
its maximum value (Prescaler is /2 * 2 = 1) in order to get the best possible resolution.
|
|
So the TIM1 counter clock is SystemCoreClock.
|
|
|
|
SystemCoreClock is set to 48 MHz for STM32F0xx Devices.
|
|
|
|
The "uwMeasuredFrequency" variable contains the measured signal frequency.
|
|
It is calculated within the capture/compare 1 interrupt service routine.
|
|
|
|
The minimum frequency value to measure is TIM1 counter clock / TIMx_CCR1 MAX
|
|
= 48 MHz / 65535
|
|
|
|
Due to TIM1_CC_IRQHandler processing time (around 2us), the maximum
|
|
frequency value to measure is around 500kHz.
|
|
|
|
TIM2_CH1 is configured to generate a PWM signal. User push-button can be used to
|
|
change the frequency of this signal from 2 kHz up to 20 kHz by steps of 2 kHz.
|
|
It is then possible to run this example without a signal generator by connecting
|
|
TIM2_CH1 to TIM1_CH1.
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_InputCapture/Inc/stm32f0xx_it.h Interrupt handlers header file
|
|
- TIM/TIM_InputCapture/Inc/main.h Header for main.c module
|
|
- TIM/TIM_InputCapture/Inc/stm32_assert.h Template file to include assert_failed function
|
|
- TIM/TIM_InputCapture/Src/stm32f0xx_it.c Interrupt handlers
|
|
- TIM/TIM_InputCapture/Src/main.c Main program
|
|
- TIM/TIM_InputCapture/Src/system_stm32f0xx.c STM32F0xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F072xB devices.
|
|
|
|
- This example has been tested with STM32F072RB-Nucleo RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM32F072RB-Nucleo RevC Set-up
|
|
- When no signal generator is used TIM2_CH1 can be connected to TIM1_CH1:
|
|
- TIM1_CH1 PA.08: connected to pin 23 of CN10 connector
|
|
- TIM2_CH1 PA.05: connected to pin 11 of CN10 connector
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|