OrgST-Microelectronics/STM32CubeF0
1
0
Fork 0
mirror of https://github.com/STMicroelectronics/STM32CubeF0.git synced 2025-05-06 19:29:12 +08:00
Code Issues Releases Wiki Activity
STM32CubeF0/Projects/STM32091C_EVAL/Examples/ADC/ADC_LowPower/Src/main.c
Ali Labbene 568c7255f7 Release v1.11.0
2019-10-18 15:22:51 +01:00

463 lines
16 KiB
C
Raw Blame History

/**
******************************************************************************
* @file ADC/ADC_LowPower/Src/main.c
* @author MCD Application Team
* @brief This example provides a short description of how to use the ADC
* peripheral to perform conversions with ADC low power modes:
* auto-wait and auto-power off.
******************************************************************************
* @attention
*
* <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "main.h"
/** @addtogroup STM32F0xx_HAL_Examples
* @{
*/
/** @addtogroup ADC_LowPower
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
#define VDD_APPLI ((uint32_t)3300) /* Value of analog voltage supply Vdda (unit: mV) */
#define RANGE_12BITS ((uint32_t)4095) /* Max value with a full range of 12 bits */
#define TIMER_FREQUENCY_HZ ((uint32_t)1000) /* Timer frequency (unit: Hz). With SysClk set to 48MHz, timer frequency TIMER_FREQUENCY_HZ range is min=1Hz, max=32.742kHz. */
/* Uncomment the line below to not use the ADC Low Power features */
#define ADC_LOWPOWER /* ADC low power modes auto-wait and auto-power off are enabled */
#define MESSAGE1 "STM32091C-EVAL"
#define MESSAGE3 "Turn potentiometer RV3(pin PC.00)"
/* Private macro -------------------------------------------------------------*/
/**
* @brief Computation of voltage (unit: mV) from ADC measurement digital
* value on range 12 bits.
* Calculation validity conditioned to settings:
* - ADC resolution 12 bits (need to scale value if using a different
* resolution).
* - Power supply of analog voltage Vdda 3.3V (need to scale value
* if using a different analog voltage supply value).
* @param ADC_DATA: Digital value measured by ADC
* @retval None
*/
#define COMPUTATION_DIGITAL_12BITS_TO_VOLTAGE(ADC_DATA) \
( (ADC_DATA) * VDD_APPLI / RANGE_12BITS)
/* Private variables ---------------------------------------------------------*/
/* ADC handler declaration */
ADC_HandleTypeDef AdcHandle;
/* TIM handler declaration */
TIM_HandleTypeDef TimHandle;
__IO uint16_t uhADCxConvertedValue = 0;
__IO uint16_t uhADCxConvertedVoltage = 0;
__IO uint8_t ubADC_overrun_status = RESET; /* Variable to report ADC overrun event from ADC error callback to main program */
/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void Error_Handler(void);
static void Display_Init(void);
static void Display(void);
static void ADC_Config(void);
static void TIM_Config(void);
/* Private functions ---------------------------------------------------------*/
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/* This sample code shows how to convert an analog input and read the converted
data using polling mode. */
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/* Initialize LEDs on board */
BSP_LED_Init(LED1);
BSP_LED_Init(LED3);
/* Configure Tamper push-button in non-interrupt mode */
BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_GPIO);
/* LCD Display init */
Display_Init();
/* Configure the ADC peripheral */
ADC_Config();
/* Run the ADC calibration */
if (HAL_ADCEx_Calibration_Start(&AdcHandle) != HAL_OK)
{
/* Calibration Error */
Error_Handler();
}
/* Configure the TIM peripheral */
TIM_Config();
/*## Enable peripherals ####################################################*/
/* Timer counter enable */
if (HAL_TIM_Base_Start(&TimHandle) != HAL_OK)
{
/* Counter Enable Error */
Error_Handler();
}
/* For this example purpose, enable ADC overrun interruption. */
/* In this ADC LowPower example, ADC overrun is not considered as an error, */
/* but as a way to watch the ADC low power modes effectiveness. */
/* Note: Enabling overrun has no usefulness except for this example purpose:*/
/* ADC overrun cannot occur with ADC low power mode "auto-wait" */
/* Usually, in normal application, overrun is enabled automatically */
/* by HAL ADC driver with functions "HAL_ADC_Start_IT()" or */
/* "HAL_ADC_Start_DMA()", but this is not compliant with low power */
/* modes. Refer to comments of parameter "LowPowerAutoWait" in HAL */
/* ADC driver definition file. */
__HAL_ADC_ENABLE_IT(&AdcHandle, (ADC_IT_OVR));
/* Start ADC conversion */
HAL_ADC_Start(&AdcHandle);
/* Wait for the first ADC conversion to be completed (timeout unit: ms) */
HAL_ADC_PollForConversion(&AdcHandle, (1000/TIMER_FREQUENCY_HZ));
/* Infinite loop */
while (1)
{
/* Wait for at least 2 ADC conversions elapsed time, to let time for */
/* potential overrun event to occur (unit: ms) */
HAL_Delay(2* (1000/TIMER_FREQUENCY_HZ));
/* Manage LED1 status in function of ADC overrun event */
if (ubADC_overrun_status != RESET)
{
/* Turn on LED1 to indicate ADC overrun event */
BSP_LED_On(LED1);
/* Reset overrun status variable for next iteration loop */
ubADC_overrun_status = RESET;
}
else
{
/* Turn off LED1 to indicate no ADC overrun event */
BSP_LED_Off(LED1);
}
/* Press Tamper push-button on STM32091C-EVAL to get the converted data */
while(BSP_PB_GetState(BUTTON_TAMPER) != GPIO_PIN_RESET);
while(BSP_PB_GetState(BUTTON_TAMPER) != GPIO_PIN_SET);
/* Get ADC1 converted data */
/* If ADC low power mode auto-wait is enabled, this release the ADC */
/* from idle mode: a new conversion will start at the next trigger */
/* event. */
uhADCxConvertedValue = HAL_ADC_GetValue(&AdcHandle);
/* Compute the voltage */
uhADCxConvertedVoltage = COMPUTATION_DIGITAL_12BITS_TO_VOLTAGE(uhADCxConvertedValue);
/* Display converted data on the LCD */
Display();
}
}
/**
* @brief System Clock Configuration
* The system Clock is configured as follow :
* System Clock source = PLL (HSE)
* SYSCLK(Hz) = 48000000
* HCLK(Hz) = 48000000
* AHB Prescaler = 1
* APB1 Prescaler = 1
* HSE Frequency(Hz) = 8000000
* PREDIV = 1
* PLLMUL = 6
* Flash Latency(WS) = 1
* @param None
* @retval None
*/
void SystemClock_Config(void)
{
RCC_ClkInitTypeDef RCC_ClkInitStruct;
RCC_OscInitTypeDef RCC_OscInitStruct;
/* Enable HSE Oscillator and Activate PLL with HSE as source */
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct)!= HAL_OK)
{
Error_Handler();
}
/* Select PLL as system clock source and configure the HCLK, PCLK1 clocks dividers */
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1);
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1)!= HAL_OK)
{
Error_Handler();
}
}
/**
* @brief ADC configuration
* @param None
* @retval None
*/
static void ADC_Config(void)
{
ADC_ChannelConfTypeDef sConfig;
/* Configuration of ADCx init structure: ADC parameters and regular group */
AdcHandle.Instance = ADCx;
AdcHandle.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV4;
AdcHandle.Init.Resolution = ADC_RESOLUTION_12B;
AdcHandle.Init.DataAlign = ADC_DATAALIGN_RIGHT;
AdcHandle.Init.ScanConvMode = ADC_SCAN_DIRECTION_FORWARD; /* Sequencer will convert the number of channels configured below, successively from the lowest to the highest channel number */
AdcHandle.Init.EOCSelection = ADC_EOC_SINGLE_CONV;
#if defined(ADC_LOWPOWER)
AdcHandle.Init.LowPowerAutoWait = ENABLE; /* Enable the dynamic low power Auto Delay: new conversion start only when the previous conversion (for regular group) or previous sequence (for injected group) has been treated by user software. */
AdcHandle.Init.LowPowerAutoPowerOff = ENABLE; /* Enable the auto-off mode: the ADC automatically powers-off after a conversion and automatically wakes-up when a new conversion is triggered (with startup time between trigger and start of sampling). */
#else
AdcHandle.Init.LowPowerAutoWait = DISABLE;
AdcHandle.Init.LowPowerAutoPowerOff = DISABLE;
#endif
AdcHandle.Init.ContinuousConvMode = DISABLE; /* Continuous mode disabled to have only 1 conversion at each conversion trig */
AdcHandle.Init.DiscontinuousConvMode = DISABLE; /* Parameter discarded because sequencer is disabled */
AdcHandle.Init.ExternalTrigConv = ADC_EXTERNALTRIGCONV_Tx_TRGO; /* Trig of conversion start done by external event */
AdcHandle.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_RISING;
AdcHandle.Init.DMAContinuousRequests = ENABLE;
AdcHandle.Init.Overrun = ADC_OVR_DATA_PRESERVED; /* Overrun set to data preserved to trig overrun event as an error in this exemple */
if (HAL_ADC_Init(&AdcHandle) != HAL_OK)
{
/* ADC initialization error */
Error_Handler();
}
/* Configuration of channel on ADCx regular group on sequencer rank 1 */
/* Note: Considering IT occurring after each ADC conversion (ADC IT */
/* enabled), select sampling time and ADC clock with sufficient */
/* duration to not create an overhead situation in IRQHandler. */
sConfig.Channel = ADCx_CHANNELa;
sConfig.Rank = ADC_RANK_CHANNEL_NUMBER;
sConfig.SamplingTime = ADC_SAMPLETIME_41CYCLES_5;
if (HAL_ADC_ConfigChannel(&AdcHandle, &sConfig) != HAL_OK)
{
/* Channel Configuration Error */
Error_Handler();
}
}
/**
* @brief TIM configuration
* @param None
* @retval None
*/
static void TIM_Config(void)
{
TIM_MasterConfigTypeDef sMasterConfig;
/* Time Base configuration */
TimHandle.Instance = TIMx;
/* Configure timer frequency */
/* Note: Setting of timer prescaler to 733 to increase the maximum range */
/* of the timer, to fit within timer range of 0xFFFF. */
/* Setting of reload period to SysClk/733 to maintain a base */
/* frequency of 1us. */
/* With SysClk set to 48MHz, timer frequency (defined by label */
/* TIMER_FREQUENCY_HZ range) is min=1Hz, max=32.742kHz. */
/* Note: Timer clock source frequency is retrieved with function */
/* HAL_RCC_GetPCLK1Freq(). */
/* Alternate possibility, depending on prescaler settings: */
/* use variable "SystemCoreClock" holding HCLK frequency, updated by */
/* function HAL_RCC_ClockConfig(). */
TimHandle.Init.Period = ((HAL_RCC_GetPCLK1Freq() / (733 * TIMER_FREQUENCY_HZ)) - 1);
TimHandle.Init.Prescaler = (733-1);
TimHandle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
TimHandle.Init.CounterMode = TIM_COUNTERMODE_UP;
TimHandle.Init.RepetitionCounter = 0x0;
TimHandle.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
if (HAL_TIM_Base_Init(&TimHandle) != HAL_OK)
{
/* Timer initialization Error */
Error_Handler();
}
/* Timer TRGO selection */
sMasterConfig.MasterOutputTrigger = TIM_TRGO_UPDATE;
sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
if (HAL_TIMEx_MasterConfigSynchronization(&TimHandle, &sMasterConfig) != HAL_OK)
{
/* Timer TRGO selection Error */
Error_Handler();
}
}
/**
* @brief Display ADC converted value on LCD
* @param None
* @retval None
*/
static void Display(void)
{
uint32_t v=0,mv=0;
uint8_t text[50];
v=(uhADCxConvertedVoltage)/1000;
mv = (uhADCxConvertedVoltage%1000)/100;
sprintf((char*)text,"V(Pot) = %ld,%ld V",v,mv);
BSP_LCD_SetTextColor(LCD_COLOR_BLACK);
BSP_LCD_DisplayStringAt(0, 145, (uint8_t*)text, CENTER_MODE);
}
/**
* @brief Display Init (LCD)
* @param None
* @retval None
*/
static void Display_Init(void)
{
/* Initialize the LCD */
BSP_LCD_Init();
/* Clear the LCD */
BSP_LCD_Clear(LCD_COLOR_WHITE);
/* Set LCD Demo description */
BSP_LCD_SetTextColor(LCD_COLOR_BLUE);
BSP_LCD_FillRect(0, 0, BSP_LCD_GetXSize(), 80);
BSP_LCD_SetTextColor(LCD_COLOR_WHITE);
BSP_LCD_SetBackColor(LCD_COLOR_BLUE);
BSP_LCD_SetFont(&Font24);
BSP_LCD_DisplayStringAt(0, 0, (uint8_t*)MESSAGE1, CENTER_MODE);
BSP_LCD_SetFont(&Font12);
BSP_LCD_DisplayStringAt(0, 30, (uint8_t*)"ADC Low Power Mode", CENTER_MODE);
BSP_LCD_DisplayStringAt(0, 45, (uint8_t*)"Press Tamper push-button", CENTER_MODE);
BSP_LCD_DisplayStringAt(0, 60, (uint8_t*)MESSAGE3, CENTER_MODE);
/* Set the LCD Text Color */
BSP_LCD_SetTextColor(LCD_COLOR_BLUE);
BSP_LCD_DrawRect(10, 90, BSP_LCD_GetXSize() - 20, BSP_LCD_GetYSize()- 100);
BSP_LCD_DrawRect(11, 91, BSP_LCD_GetXSize() - 22, BSP_LCD_GetYSize()- 102);
BSP_LCD_SetFont(&Font24);
BSP_LCD_SetBackColor(LCD_COLOR_WHITE);
}
/**
* @brief ADC error callback in non blocking mode
* (ADC conversion with interruption or transfer by DMA)
* @param hadc: ADC handle
* @retval None
*/
void HAL_ADC_ErrorCallback(ADC_HandleTypeDef *hadc)
{
/* In this ADC LowPower example, ADC overrun is not considered as an error, */
/* but as a way to watch the ADC low power modes effectiveness. */
/* Differentiation of ADC error overrun versus other potential errors: */
if (HAL_ADC_GetError(hadc) == HAL_ADC_ERROR_OVR)
{
/* Update variable to report ADC overrun event to main program */
ubADC_overrun_status = SET;
}
else
{
/* In case of ADC error, call main error handler */
Error_Handler();
}
}
/**
* @brief This function is executed in case of error occurrence.
* @param None
* @retval None
*/
static void Error_Handler(void)
{
/* User may add here some code to deal with a potential error */
/* In case of error, LED3 is toggling at a frequency of 1Hz */
while (1)
{
/* Toggle LED3 */
BSP_LED_Toggle(LED3);
HAL_Delay(500);
}
}
#ifdef USE_FULL_ASSERT
/**
* @brief Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* @param file: pointer to the source file name
* @param line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t *file, uint32_t line)
{
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* Infinite loop */
while (1)
{
}
}
#endif
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
Reference in New Issue View Git Blame Copy Permalink