/** ****************************************************************************** * @file CEC/CEC_MultiAddress/Src/main.c * @author MCD Application Team * @brief This example describes how to configure and use the CEC through * the STM32F0xx HAL API. ****************************************************************************** * @attention * *

© Copyright (c) 2016 STMicroelectronics. * All rights reserved.

* * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the * License. You may obtain a copy of the License at: * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "main.h" /** @addtogroup STM32F0xx_HAL_Examples * @{ */ /** @addtogroup CEC_MultiAddress * @{ */ /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ uint8_t Tab_Rx[CEC_MAX_PAYLOAD]; /* Received data buffer. Max size = 16 bytes * header + opcode followed by up to 14 operands */ uint8_t Tab_Tx[CEC_MAX_PAYLOAD-1]; /* Transmitted data buffer. * header is not included in Tab_Tx. * Max size = 15 bytes. * one opcode followed by up to 14 operands. * When payload size = 0, only the header is sent * (ping operation) */ uint8_t ReceivedFrame = 0x0; /* Set when a reception occurs */ uint16_t NbOfReceivedBytes = 0x0; /* Number of received bytes in addition to the header. * when a ping message has been received (header * only), NbOfReceivedBytes = 0 */ uint8_t StartSending = 0x0; /* Set when a transmission is triggered by the user */ uint32_t TxSize = 0x0; /* Number of bytes to transmit in addition to the header. * In case of ping operation (only the header sent), * TxSize = 0 */ uint8_t InitiatorAddress1 = 0x0; /* Transmitter logical address 1 */ uint8_t InitiatorAddress2 = 0x0; /* Transmitter logical address 2 (if applicable) */ uint8_t MyFollowerAddress1 = 0x0; /* Destination logical address 1 */ uint8_t MyFollowerAddress2 = 0x0; /* Destination logical address 2 (if applicable) */ uint8_t DestinationAddress = 0x0; /* Destination logical address, set on the * fly based on the button pushed by the user */ __IO uint8_t TxStatus = 0; CEC_HandleTypeDef hcec; /* Private function prototypes -----------------------------------------------*/ void SystemClock_Config(void); static void CEC_Config(CEC_HandleTypeDef *hcec); static void CEC_FlushRxBuffer(void); /* Private functions ---------------------------------------------------------*/ /** * @brief Main program * @param None * @retval None */ int main(void) { /* This sample code shows how to use STM32F0xx CEC HAL API to transmit and * receive data. The device is set in waiting to receive mode and sends * messages when the evaluation board buttons are pushed by the user */ /* STM32F0xx HAL library initialization: - Configure the Flash prefetch - Systick timer is configured by default as source of time base, but user can eventually implement his proper time base source (a general purpose timer for example or other time source), keeping in mind that Time base duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and handled in milliseconds basis. - Low Level Initialization */ HAL_Init(); /* Configure the system clock to 48 MHz */ SystemClock_Config(); /* -1- Initialize LEDs mounted on EVAL board */ /* Configure LED1, LED2, LED3 and LED4 */ BSP_LED_Init(LED1); BSP_LED_Init(LED2); BSP_LED_Init(LED3); BSP_LED_Init(LED4); /* -2- Configure Tamper push-button in Interrupt mode */ /* button-triggered interruptions initialization */ BSP_PB_Init(BUTTON_TAMPER,BUTTON_MODE_EXTI); /* -3- Configure Joystick Sel push-button in Interrupt mode */ BSP_JOY_Init(JOY_MODE_EXTI); /* CEC device initialization */ #if defined (DEVICE_1) /* Device 1: * a single logical address ... */ InitiatorAddress1 = DEVICE_ADDRESS_1; /* ... and two different follower addresses */ MyFollowerAddress1 = DEVICE_ADDRESS_2; MyFollowerAddress2 = DEVICE_ADDRESS_3; #elif defined (DEVICE_2) /* Device 2: * two different logical addresses ... */ InitiatorAddress1 = DEVICE_ADDRESS_2; InitiatorAddress2 = DEVICE_ADDRESS_3; /* ... and a single follower address */ MyFollowerAddress1 = DEVICE_ADDRESS_1; #endif /* DEVICE_1 */ /* -4- CEC configuration (transfer will take place in Interrupt mode) */ hcec.Instance = CEC; /* Deinitialize CEC to reinitialize from scratch */ HAL_CEC_DeInit(&hcec); /* IP configuration */ CEC_Config(&hcec); /* -5- CEC transfer general variables initialization */ ReceivedFrame = 0; StartSending = 0; NbOfReceivedBytes = 0; CEC_FlushRxBuffer(); while (1) { /* if no reception has occurred and no error has been detected, transmit a message if the user has pushed a button */ while( (StartSending == 1) && (ReceivedFrame == 0)) { HAL_CEC_Transmit_IT(&hcec,InitiatorAddress1 ,DestinationAddress, (uint8_t *)&Tab_Tx, TxSize); /* loop until TX ends or TX error reported */ while (TxStatus != 1); StartSending = 0; TxStatus = 0; } /* if a frame has been received */ if (ReceivedFrame == 1) { /* Test on the Destination Logical Address * (code applicable whatever the device): * if Receiver has address 0x01 */ if ((Tab_Rx[0]&0x0F) == 0x01) { /* Turn on LED1 */ BSP_LED_On(LED1); /* Turn on LED4 */ BSP_LED_On(LED4); /* Turn off LED3 */ BSP_LED_Off(LED3); } /* if Receiver has address 0x03 */ else if ((Tab_Rx[0]&0x0F) == 0x03) { /* Turn on LED1 */ BSP_LED_On(LED1); /* Turn off LED4 */ BSP_LED_Off(LED4); /* Turn off LED3 */ BSP_LED_Off(LED3); } /* if Receiver has address 0x05 */ else if ((Tab_Rx[0]&0x0F) == 0x05) { /* Turn on LED4 */ BSP_LED_On(LED4); /* Turn off LED1 */ BSP_LED_Off(LED1); /* Turn off LED3 */ BSP_LED_Off(LED3); } /* if Broadcast message */ else if ((Tab_Rx[0]&0x0F) == 0x0F) { /* Turn off all LEDs */ BSP_LED_Off(LED1); BSP_LED_Off(LED2); BSP_LED_Off(LED3); BSP_LED_Off(LED4); } ReceivedFrame = 0; CEC_FlushRxBuffer(); } else if (ReceivedFrame == 2) /* means CEC error detected */ { /* Turn on LED3 */ BSP_LED_On(LED3); ReceivedFrame = 0; } } } /** * @brief Configures the CEC peripheral. * @param None * @retval None */ static void CEC_Config(CEC_HandleTypeDef *hcec) { /* CEC configuration parameters */ #if defined (DEVICE_1) hcec->Init.OwnAddress = CEC_OWN_ADDRESS_1; #elif defined (DEVICE_2) hcec->Init.OwnAddress = CEC_OWN_ADDRESS_3|CEC_OWN_ADDRESS_5; #endif hcec->Init.SignalFreeTime = CEC_DEFAULT_SFT; hcec->Init.Tolerance = CEC_STANDARD_TOLERANCE; hcec->Init.BRERxStop = CEC_NO_RX_STOP_ON_BRE; hcec->Init.BREErrorBitGen = CEC_BRE_ERRORBIT_NO_GENERATION; hcec->Init.LBPEErrorBitGen = CEC_LBPE_ERRORBIT_NO_GENERATION; hcec->Init.BroadcastMsgNoErrorBitGen = CEC_BROADCASTERROR_NO_ERRORBIT_GENERATION; hcec->Init.SignalFreeTimeOption = CEC_SFT_START_ON_TXSOM; hcec->Init.ListenMode = CEC_REDUCED_LISTENING_MODE; hcec->Init.RxBuffer = Tab_Rx; HAL_CEC_Init(hcec); } /** * @brief Tx Transfer completed callback * @param hcec: CEC handle * @retval None */ void HAL_CEC_TxCpltCallback(CEC_HandleTypeDef *hcec) { TxStatus = 1; } /** * @brief Rx Transfer completed callback * @param hcec: CEC handle * @retval None */ void HAL_CEC_RxCpltCallback(CEC_HandleTypeDef *hcec, uint32_t RxFrameSize) { ReceivedFrame = 1; } /** * @brief CEC error callbacks * @param hcec: CEC handle * @retval None */ void HAL_CEC_ErrorCallback(CEC_HandleTypeDef *hcec) { ReceivedFrame = 2; } /** * @brief Reset CEC reception buffer * @param None * @retval None */ static void CEC_FlushRxBuffer(void) { uint32_t cpt; for (cpt = CEC_MAX_PAYLOAD; cpt > 0; cpt--) { Tab_Rx[cpt-1] = 0; } } /** * @brief EXTI line detection callbacks * @param GPIO_Pin: Specifies the pins connected EXTI line * @retval None */ void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin) { if(GPIO_Pin == TAMPER_BUTTON_PIN) { /* Toggle GREEN LED1 */ BSP_LED_Toggle(LED1); DestinationAddress = MyFollowerAddress1; TxSize = 0x0; /* no payload, ping only */ StartSending = 1; } if(GPIO_Pin == DOWN_JOY_PIN) { /* Toggle BLUE LED4 */ BSP_LED_Toggle(LED4); #if defined (DEVICE_1) DestinationAddress = MyFollowerAddress2; #elif defined (DEVICE_2) DestinationAddress = MyFollowerAddress1; #endif /* DEVICE_1 */ TxSize = 0x0; /* no payload, ping only */ StartSending = 1; } if(GPIO_Pin == SEL_JOY_PIN) { /* Toggle ORANGE LED2 */ BSP_LED_Toggle(LED2); DestinationAddress = 0xF; /* broadcast message indicator */ TxSize = 0x0; /* no payload, ping only */ StartSending = 1; } } /** * @brief System Clock Configuration * The system Clock is configured as follow : * System Clock source = PLL (HSE) * SYSCLK(Hz) = 48000000 * HCLK(Hz) = 48000000 * AHB Prescaler = 1 * APB1 Prescaler = 1 * HSE Frequency(Hz) = 8000000 * PREDIV = 1 * PLLMUL = 6 * Flash Latency(WS) = 1 * @param None * @retval None */ void SystemClock_Config(void) { RCC_ClkInitTypeDef RCC_ClkInitStruct; RCC_OscInitTypeDef RCC_OscInitStruct; /* Enable HSE Oscillator and Activate PLL with HSE as source */ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; RCC_OscInitStruct.HSEState = RCC_HSE_ON; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1; RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6; if (HAL_RCC_OscConfig(&RCC_OscInitStruct)!= HAL_OK) { /* Initialization Error */ while(1); } /* Select PLL as system clock source and configure the HCLK, PCLK1 clocks dividers */ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1); RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1)!= HAL_OK) { /* Initialization Error */ while(1); } } #ifdef USE_FULL_ASSERT /** * @brief Reports the name of the source file and the source line number * where the assert_param error has occurred. * @param file: pointer to the source file name * @param line: assert_param error line source number * @retval None */ void assert_failed(uint8_t* file, uint32_t line) { /* User can add his own implementation to report the file name and line number, ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ /* Infinite loop */ while (1) { } } #endif /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/