STM32CubeF0/Projects/STM32091C_EVAL/Examples/BSP/readme.txt

/**
  @page BSP  Example on how to use the BSP drivers
  
  @verbatim
  ******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
  * @file    BSP/readme.txt 
  * @author  MCD Application Team
  * @brief   Description of the BSP example.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  @endverbatim

@par Example Description 

This example provides a description of how to use the different BSP drivers. 

At the beginning of the main program the HAL_Init() function is called to reset 
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 48 MHz.

This example shows how to use the different functionalities of components 
available on the board by switching between all tests using Tamper push-button button. 

 ** Push the User button to start first Test.  
Blue Led (LD4) will blink between each test. Press Tamper push-button to start another test:

 ** JOYSTICK **
Use the joystick button to move a pointer inside a rectangle 
(up/down/right/left) and change the pointer color(select).

 ** LCD **
This example shows how to use the different LCD features to display string
with different fonts, to display different shapes and to draw a bitmap.

 ** SD **
This example shows how to erase, write and read the SD card and also 
how to detect the presence of the card.

 ** EEPROM **
This example show how to read and write data in EEPROM I2C M24LR64 connected on STM32091C-EVAL
   * The I2C RF EEPROM memory (M24LR64) is available through the connector CN2

 ** TSENSOR **
This example show how to read a Temperature using the temperature sensor.

 ** LCD LOG **
This example show how to use the LCD log features. 

@par Directory contents 

  - BSP/Src/main.c                 Main program
  - BSP/Src/system_stm32f0xx.c     STM32F0xx system clock configuration file
  - BSP/Src/stm32f0xx_it.c         Interrupt handlers 
  - BSP/Src/joystick.c             joystick feature
  - BSP/Src/lcd.c                  LCD drawing features
  - BSP/Src/log.c                  LCD Log firmware functions
  - BSP/Src/sd.c                   SD features
  - BSP/Src/eeprom.c               EEPROM Read/Write features
  - BSP/Src/temperature_sensor.c   Temperature Sensor features
  - BSP/Inc/main.h                 Main program header file  
  - BSP/Inc/stm32f0xx_conf.h       HAL Configuration file
  - BSP/Inc/stm32f0xx_it.h         Interrupt handlers header file
  - BSP/Inc/lcd_log_conf.h         lcd_log configuration template file
  - BSP/Inc/stlogo.h               Image used for BSP example
        
@par Hardware and Software environment  

  - This example runs on STM32F0xx devices.
    
  - This example has been tested with STMicroelectronics STM32091C-EVAL
    evaluation boards and can be easily tailored to any other supported device 
    and development board.
  
@par How to use it ? 

In order to make the program work, you must do the following :
 - Open your preferred toolchain 
 - Rebuild all files and load your image into target memory
 - Run the example

 * <h3><center>&copy; COPYRIGHT STMicroelectronics</center></h3>
 */